MONTOUR FALLS,, NY —
OSHA Inspection: SHEPARD NILES INC.
Special Programs inspection · Safety discipline
At a glance
On , OSHA opened a special Programs safety inspection of SHEPARD NILES INC. in 250 N. GENESSE ST., MONTOUR FALLS,, NY 14865 (NAICS 000000). OSHA activity number 300632353.
Where did this inspection happen?
- Establishment
- SHEPARD NILES INC.
- Site address
- 250 N. GENESSE ST.
- City
- MONTOUR FALLS,
- State
- NY
- ZIP
- 14865
What kind of inspection was it?
- Inspection type
- Special Programs (K)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Y
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 3536
- Employees
- 205
- Ownership type
- A
Citations
39 citations on file for this inspection.
5(a)(1)
- Issued
- Abate by
- Penalty
- Initial $1400.00 · Current $1400.00
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazard of being pulled into and crushed by the rotating parts of a pipe threading machine: a)Machine Shop, boiler room, on or about 01/28/99: Employee(s) operate a Oster 545 Pipe Threading Machine, which was activated by a manually operated "on/off" switch that would not automatically shut the machine off if its operator was inadvertently caught up in its rotating parts. b)Bridge Shop, on or about 02/04/99: Employee(s) operate a Oster 545 Pipe Threading Machine, which was activated by a manually operated "on/off" switch that would not automatically shut the machine off if its operator was inadvertently caught up in its rotating parts. Among other methods, one feasible method to reduce this hazard is to establish and enforce adequate safe operating procedures, such as those stipulated in American National Standards for Portable Pipe Threading Machines (ANSI B208.1-1982). Elements essential to an acceptable safe operating procedure include at a minimum: 1) Installation of a momentary contact device (deadman foot switch) to control power input to the machine. This device would automatically stop the machine and the rotating parts if the operator's foot was removed from the foot switch for any reason. 2) Provide training and education to the machine operators concerning all the appropriate procedures for the safe operation and use of this type of machinery.
Recent events (2)
- — J (S) $1400.00
- — Z (S) $1400.00
5(a)(1)
- Issued
- Abate by
- Penalty
- Initial $1750.00 · Current $1225.00 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to a crushing hazard when working at locations on the conveyor system where emergency stop devices were not functioning: a)Bridge Shop, Tarca Beam Line, on or about 02/22/99: Employee(s) operating the conveyor for the Tarca Beam Straightener were not provided with a functioning emergency stop button. b)Bridge Shop, Tarca Beam Line, on or about 02/22/99: Employee(s) operating the conveyor for the Cleveland Press, serial number on control panel 640794, were not provided with a functioning emergency stop button. Among other methods, one feasible and acceptable abatement method to correct this hazard is the installation of properly functioning emergency stop buttons. REF: American National Standard Safety Standard for Conveyors and related equipment, ANSI B20.1-1976: section 5 General Safety Standards, Rule 5.11.2.3.
Recent events (2)
- — J (S) $1225.00
- — Z (S) $1750.00
5(a)(1)
- Issued
- Abate by
- Penalty
- Initial $1750.00 · Current $1225.00 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazard of being struck by the load should the overhead hoist or below-the-hook lifting devices fail: a)Building # 3, Bridge Shop, on or about 01/14/99 through 03/11/99: The following below the hook lifting devices had no rated load markings and no initial, frequent or periodic inspections performed, including, but not limited to: 1) Seven 6 inch wide x 1 inch beam clamps. 2) A 70 1/2 inch long tongs x 5 1/2 inch lips. 3) A 21 inch long tongs x 2 1/2 inch lips. 4) A set of 18 inch long tongs x 1 7/8 inch lips. Among other methods, several feasible and acceptable abatement methods to correct each of these hazards are to: 1.Prior to initial use, all new, modified or repaired lifting devices shall be inspected by a designated person and an operational test performed to verify compliance. 2.Mark the rated load capacity of the lifting device on the main structure or equivalent. 3.Conduct frequent and periodic inspections of the lifting devices for wear, deterioration or malfunction in accordance with ASME B30.20. b)On or about 01/14/99 through 03/12/99, the following overhead hoists had mislabelled load markings, missing hook safety latch, and had not received frequent and periodic inspections, including but not limited to: 1)Building # 3, Bridge Shop, Tarca Line: A Shepard Niles underhung 2 ton electric wire rope hoist, Crane # 80 had a missing hook throat latch and had not received frequent and periodic inspections of all critical items. 3)Building # 3, Bridge Shop, Tarca Line: Crane # 78, the sheave guard stated that the crane was a 1 ton, and on the bridge it stated that it was a 2 ton crane. Among other methods, one feasible and acceptable abatement method to correct the hazard is to: 1. Install safety hook throat latches. 2. Clearly label sheave guard and bridge to be the same tonnage for the cranes.
Recent events (2)
- — J (S) $1225.00
- — Z (S) $1750.00
1910.22 A01
- Issued
- Abate by
- Penalty
- Initial $1050.00 · Current $735.00 Reduced
Recent events (2)
- — J (S) $735.00
- — Z (S) $1050.00
1910.22 A02
- Issued
- Abate by
Recent events (2)
- — J (S)
- — Z (S)
1910.22 B01
- Issued
- Abate by
Recent events (2)
- — J (S)
- — Z (S)
1910.23 A08
- Issued
- Abate by
- Penalty
- Initial $1400.00 · Current $980.00 Reduced
Recent events (2)
- — J (S) $980.00
- — Z (S) $1400.00
1910.147 C04 II
- Issued
- Abate by
- Penalty
- Initial $1750.00 · Current $1225.00 Reduced
Recent events (2)
- — J (S) $1225.00
- — Z (S) $1750.00
1910.147 C06 IC
- Issued
- Abate by
- Penalty
- Initial $1750.00 · Current $1225.00 Reduced
Recent events (2)
- — J (S) $1225.00
- — Z (S) $1750.00
1910.178 N04
- Issued
- Abate by
- Penalty
- Initial $1400.00 · Current $980.00 Reduced
Recent events (2)
- — J (S) $980.00
- — Z (S) $1400.00
1910.179 G06
- Issued
- Abate by
- Penalty
- Initial $1750.00 · Current $1225.00 Reduced
Recent events (2)
- — J (S) $1225.00
- — Z (S) $1750.00
1910.184 I09 III
- Issued
- Abate by
- Penalty
- Initial $1750.00 · Current $1225.00 Reduced
Recent events (2)
- — J (S) $1225.00
- — Z (S) $1750.00
1910.212 A01
- Issued
- Abate by
- Penalty
- Initial $3500.00 · Current $2450.00 Reduced
Recent events (2)
- — J (S) $2450.00
- — Z (S) $3500.00
1910.212 A03 II
- Issued
- Abate by
- Penalty
- Initial $3500.00 · Current $2450.00 Reduced
Recent events (3)
- — P (S) $2450.00
- — J (S) $2450.00
- — Z (S) $3500.00
1910.213 B03
- Issued
- Abate by
- Penalty
- Initial $1400.00 · Current $980.00 Reduced
Recent events (2)
- — J (S) $980.00
- — Z (S) $1400.00
1910.213 H04
- Issued
- Abate by
- Penalty
- Initial $1400.00 · Current $980.00 Reduced
Recent events (2)
- — J (S) $980.00
- — Z (S) $1400.00
1910.217 B04 II
- Issued
- Abate by
- Penalty
- Initial $1050.00 · Current $735.00 Reduced
Recent events (2)
- — J (S) $735.00
- — Z (S) $1050.00
1910.217 B07 VA
- Issued
- Abate by
- Penalty
- Initial $1750.00 · Current $1225.00 Reduced
Recent events (2)
- — J (S) $1225.00
- — Z (S) $1750.00
1910.217 C01 I
- Issued
- Abate by
- Penalty
- Initial $3500.00 · Current $2450.00 Reduced
Recent events (2)
- — J (S) $2450.00
- — Z (S) $3500.00
1910.217 D09 IV
- Issued
- Abate by
- Penalty
- Initial $1750.00 · Current $1225.00 Reduced
Recent events (2)
- — J (S) $1225.00
- — Z (S) $1750.00
1910.217 E01 I
- Issued
- Abate by
- Penalty
- Initial $1750.00 · Current $1225.00 Reduced
Recent events (2)
- — J (S) $1225.00
- — Z (S) $1750.00
1910.217 F02
- Issued
- Abate by
Recent events (2)
- — J (S)
- — Z (S)
1910.219 C02 I
- Issued
- Abate by
- Penalty
- Initial $1050.00 · Current $1050.00
Recent events (2)
- — J (S) $1050.00
- — Z (S) $1050.00
1910.219 D01
- Issued
- Abate by
- Penalty
- Initial $1750.00 · Current $1225.00 Reduced
Recent events (2)
- — J (S) $1225.00
- — Z (S) $1750.00
1910.219 E01 I
- Issued
- Abate by
Recent events (2)
- — J (S)
- — Z (S)
1910.219 E03 I
- Issued
- Abate by
Recent events (2)
- — J (S)
- — Z (S)
1910.219 F01
- Issued
- Abate by
- Penalty
- Initial $1750.00 · Current $1225.00 Reduced
Recent events (2)
- — J (S) $1225.00
- — Z (S) $1750.00
1910.219 F03
- Issued
- Abate by
Recent events (2)
- — J (S)
- — Z (S)
1910.242 B
- Issued
- Abate by
- Penalty
- Initial $1400.00 · Current $980.00 Reduced
Recent events (2)
- — J (S) $980.00
- — Z (S) $1400.00
1910.253 B04 III
- Issued
- Abate by
- Penalty
- Initial $1400.00 · Current $980.00 Reduced
Recent events (2)
- — J (S) $980.00
- — Z (S) $1400.00
1910.303 G02 I
- Issued
- Abate by
- Penalty
- Initial $1750.00 · Current $1225.00 Reduced
Recent events (2)
- — J (S) $1225.00
- — Z (S) $1750.00
1910.304 A02
- Issued
- Abate by
- Penalty
- Initial $1750.00 · Current $1225.00 Reduced
Recent events (2)
- — J (S) $1225.00
- — Z (S) $1750.00
1910.304 F05 V
- Issued
- Abate by
Recent events (2)
- — J (S)
- — Z (S)
1910.332 B01
- Issued
- Abate by
- Penalty
- Initial $1750.00 · Current $1225.00 Reduced
Recent events (2)
- — J (S) $1225.00
- — Z (S) $1750.00
1910.333 B02 I
- Issued
- Abate by
Recent events (2)
- — J (S)
- — Z (S)
1910.335 A01 I
- Issued
- Abate by
Recent events (2)
- — J (S)
- — Z (S)
1910.179 J02
- Issued
- Abate by
- Penalty
- Initial $44000.00 · Current $30800.00 Reduced
Recent events (2)
- — J (U) $30800.00
- — Z (W) $44000.00
1910.179 J03
- Issued
- Abate by
Recent events (2)
- — J (U)
- — Z (W)
1910.303 F
- Issued
- Abate by
Recent events (2)
- — J (O)
- — Z (O)
More inspections at SHEPARD NILES INC.
MONTOUR FALLS,, NY—1999-01-14 00:00:00
SHEPARD NILES INC.
MONTOUR FALLS,, NY—1990-05-07 00:00:00
SHEPARD NILES INC.
MONTOUR FALLS,, NY—1988-12-20 00:00:00
SHEPARD NILES INC.
MONTOUR FALLS,, NY—1988-10-05 00:00:00
SHEPARD NILES INC.
MONTOUR FALLS,, NY—1988-04-26 00:00:00
SHEPARD NILES INC.
View SHEPARD NILES INC.'s full OSHA safety record →
More inspections in this industry (NAICS 000000)
SCHENECTADY, NY—2012-01-05 00:00:00
BRUCE D. BOWMAN
BILLINGS, MT—2005-01-25 00:00:00
KGC, INC.
ROCKAWAY, NJ—2002-12-31 00:00:00
ROCKAWAY BOROUGH DPW
FOREST CITY, NC—2002-12-31 00:00:00
HARRY BRICKEY DBA A. BRICKEY CEILING COMPANY
EDGERTON, KS—2002-12-31 00:00:00
SUDDEN BOND INDUSTRIES
More inspections in NY
MAYVILLE, NY—2026-07-16
MAYVILLE VILLAGE DPW
NEW HYDE PARK, NY—2026-07-16
NORTH HEMPSTEAD TN MICHAEL J TULLY PARK
CONESUS, NY—2026-07-16
CONESUS TN HIGHWAY DEPT
COMSTOCK, NY—2026-07-15
NYSDOCCS WASHINGTON CORRECTIONAL FACILITY
BALDWINSVILLE, NY—2026-07-15
LYSANDER TOWN HIGHWAY DEPARTMENT
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 300632353.