WARREN, OH — 2007-09-05 00:00:00

OSHA Inspection: JKT TRUCKING

Complaint inspection · Safety discipline

At a glance

On 2007-09-05 00:00:00, OSHA opened a complaint safety inspection of JKT TRUCKING in 641 GRISWOLD ST. NE, WARREN, OH 44483 (NAICS 423930). OSHA activity number 311162366.

Watch JKT Trucking — free Get an email when a new federal OSHA severe-injury report for JKT Trucking is published. One employer, no account, unsubscribe in one click.

Where did this inspection happen?

Establishment: JKT TRUCKING
Site address: 641 GRISWOLD ST. NE
City: WARREN
State: OH
ZIP: 44483

What kind of inspection was it?

Inspection type: Complaint (B)
Scope: Partial (B)
Discipline: Safety
Advance notice: No
Union status: N

When did the case open and close?

Opened: 2007-09-05 00:00:00
Closing conference: 2007-09-06 00:00:00
Case closed: 2008-05-14 00:00:00
Last modified: 2009-07-06 00:00:00
Data loaded: 2011-10-14 16:38:47

Establishment context

NAICS code: 423930
SIC code (legacy): 5093
Employees: 12
Ownership type: A

Citations

10 citations on file for this inspection.

5(a)(1)

Serious Gravity 03 1 instance 3 exposed

Issued: 2008-02-25 00:00:00
Abate by: 2008-03-14 00:00:00
Penalty: Initial $750.00 · Current $750.00

General-duty citation text

5(a)(1):  Section 5(a)(1) of the Occupational Safety and Health Act of
1970:  the employer did not furnish
employment and a place of employment which were free from recognized
hazards that were causing or likely
to cause death or serious physical harm to employees.
Section 5(a)(1) of the Occupational Safety and Health Act of 1970:  the
employer did not furnish employment
and a place of employment which were free from recognized hazards that
were causing or likely to cause
death or serious physical harm to employees, in that employees were
exposed to impact and puncture hazards
caused by chipping off of the Enterprise hydraulic shear blade's cutting
edges.  Improperly adjusted blade
clearance may cause accelerated blade heating and expansion or poor
cutting and chipping of the blade's
cutting edges.  Feasible and acceptable abatement methods to correct this
hazard include: A) Ensure the initial
and continuing competence of inspection and maintenance personnel through
proper training, as referenced in
ANSI Z268.1-1982, Safety Requirements for Design, Use, and Maintenance of
Metal Scrap Processing
Equipment; and B) ensure the shear blades are properly installed and
shimmed
in accordance with the
manufacturer's, The Enterprise Company,  hydraulic shear, Shear Blade
Maintenance & Installation manual.

1910.133 A01

Serious Gravity 01 1 instance 3 exposed

Issued: 2008-02-25 00:00:00
Abate by: 2008-03-19 00:00:00
Penalty: Initial $450.00 · Current $450.00

1910.147 C01

Serious Gravity 03 1 instance 12 exposed

Issued: 2008-02-25 00:00:00
Abate by: 2008-03-29 00:00:00
Penalty: Initial $750.00 · Current $750.00

1910.157 G02

Serious Gravity 01 1 instance 12 exposed

Issued: 2008-02-25 00:00:00
Abate by: 2008-03-29 00:00:00
Penalty: Initial $450.00 · Current $450.00