OSHA Inspection: THE CHATEAU RESIDENCE CLUB

Issued

2012-08-17 00:00:00

Abate by

2012-09-01 00:00:00

Penalty

Initial $1607.00 · Current $965.00 Reduced

General-duty citation text

29 CFR 1910.176(b): Material stored in tiers was not stacked, blocked, interlocked or limited in height so that it was stable and secure against sliding and collapse:    (a)The Chateau Residence Club @ 17 Chateau Lane, Beaver Creek, CO. Storage Room. On or before April 18, 2012, the employer did not ensure that the wood pieces and other materials on the metal rack were adequately stacked to prevent them from falling. This condition exposed employees to the hazard of being struck by unstable materials.

Issued

2012-08-17 00:00:00

Abate by

2012-09-01 00:00:00

Penalty

Initial $2142.00 · Current $1285.00 Reduced

General-duty citation text

29 CFR 29 CFR 1910.212(a)(3)(ii):  Point(s) of operation of machinery were not guarded to prevent employee(s) from having any part of their body in the danger zone(s) during operating cycle(s):    (a)The Chateau Residence Club @ 17 Chateau Lane, Beaver Creek, CO. Wood Shop. On or before April 18, 2012, the employer did not ensure that the Vertical Band Saw was equipped with adequate point-of-operation blade guarding to protect employees against amputation hazards during the operating cycles.    Abatement Note:  Abatement certification is required for this item (see enclosed "Certification of Corrective Action Worksheet").

Issued

2012-08-17 00:00:00

Abate by

2012-09-01 00:00:00

Penalty

Initial $2678.00 · Current $1606.00 Reduced

General-duty citation text

29 CFR 1910.213(d)(1):  Circular handfed crosscut table saw was not guarded with an automatically adjusting hood which completely enclosed that portion of the saw above the table and above the material being cut:    (a)The Chateau Residence Club @ 17 Chateau Lane, Beaver Creek, CO. Wood Shop. On or before April 18, 2012, the employer did not ensure that the blade of Delta Rockwell 12  table saw was provided with an adequate guard to prevent the operator from having any part of his body in the zone of danger during the operation cycle. This condition exposed the employees to an amputation hazard created by point of operation due to an unguarded table saw blade     Abatement Note:  Abatement certification is required for this item (see enclosed "Certification of Corrective Action Worksheet").

Issued

2012-08-17 00:00:00

Abate by

2012-09-01 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.213(p)(4): Belt sanding machines shall be provided with guards at each nip point where the sanding belt runs on to a pulley. These guards shall effectively prevent the hands or fingers of the operator from coming in contact with the nip points. The unused run of the sanding belt shall be guarded against accidental contact.    (a) The Chateau Residence Club @ 17 Chateau Lane, Beaver Creek, CO. Wood Shop. On or before April 18, 2012, the employer did not ensure that the horizontal sander was provided with adequate guarding to protect employees from hazards such as those created by In-Running Nip Points (Pinch Points) and accident contact from the unused run of the sanding belt during operating cycles.      Abatement Note:  Abatement certification is required for this item (see enclosed "Certification of Corrective Action Worksheet").

Issued

2012-08-17 00:00:00

Abate by

2012-09-01 00:00:00

Penalty

Initial $1890.00 · Current $1134.00 Reduced

General-duty citation text

29 CFR 1910.213(s)(6):  Woodworking equipment areas were not maintained effectively to prevent fires due to accumulation of wood dust:    (a)The Chateau Residence Club @ 17 Chateau Lane, Beaver Creek, CO. Wood Shop. On or before April 18, 2012, the employer did not ensure wood dust was cleaned through an effective housekeeping program and subsequently was allowed to accumulate in quantities on the Router Work Bench Area, Electrical Relocatable Power Strips in Tool Wall and Floor Area(s).  This condition exposed employees to a fire hazard.

Issued

2012-08-17 00:00:00

Abate by

2012-09-01 00:00:00

Penalty

Initial $2142.00 · Current $1285.00 Reduced

General-duty citation text

29 CFR 1910.219(d)(1): Pulleys with parts seven feet or less from the floor or platform were not guarded in accordance with the requirements specified in 1910.219(m) and (o) to adequately guard the nip-point of the belt and pulley.    (a)The Chateau Residence Club @ 17 Chateau Lane, Beaver Creek, CO. Wood Shop. On or before April 18, 2012, the employer did not ensure that the belt and pulley on the power drive of the Vertical Band Saw was equipped with adequate guarding to protect employees from hazards such as those created by In-Running Nip Points (Pinch Points) during operating cycles.

Issued

2012-08-17 00:00:00

Abate by

2012-09-01 00:00:00

Penalty

Initial $1607.00 · Current $965.00 Reduced

General-duty citation text

CFR 1910.242(b): Compressed air used for cleaning was not reduced to less than 30 p.s.i.    (a)The Chateau Residence Club @ 17 Chateau Lane, Beaver Creek, CO. Storage Room. On or before April 18, 2012, the employer did not ensure that the compressed air used by employees for cleaning purposes in the wood shop was reduced to less than 30 p.s.i. operating pressure as required under the standard. This condition exposed employees to the hazard of compressed air embolisms or eye/skin penetration of flying particles.

Issued

2012-08-17 00:00:00

Abate by

2012-09-01 00:00:00

Penalty

Initial $2142.00 · Current $1260.00 Reduced

General-duty citation text

29 CFR 1910.305(a)(2)(ix):  All lamps for general use illumination shall be protected from accidental contact or breakage by a suitable fixture or lamp holder with a guard:    (a)The Chateau Residence Club @ 17 Chateau Lane, Beaver Creek, CO. Storage Room. On or before April 18, 2012, the employer did not ensure that the florescent light at the storage room approximately 3 feet above the floor was protected from accidental contact or breakage by a suitable fixture or lamphholder with a guard:  This condition exposed employees to an electrical hazard.

Issued

2012-08-17 00:00:00

Abate by

2012-09-01 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.305(b)(3)(ii): Each outlet box in completed installation was not closed by suitable covers securely fastened in place.    (a) The Chateau Residence Club @ 17 Chateau Lane, Beaver Creek, CO.  Wood Shop.  On or before April 18, 2012, the employer did not ensure that the 220-volt receptacle outlet in completed installation on the wall was closed by a suitable cover securely fastened in place.  The condition exposed the employees to an electrical hazard.

Issued

2012-08-17 00:00:00

Abate by

2012-09-01 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.305(g)(1)(iv) (A): Flexible cords and cables were being used as a substitute for the fixed wiring of the structure:    The Chateau Residence Club @ 17 Chateau Lane, Beaver Creek, CO. On or before April 18, 2012,  a relocatable power strip, used as a substitute for the fixed wiring of the structure, was being used with an extension cords (daisy chain) to power different tools such as, but not limited to portable  air compressor, router, vacuum cleaner, and other tools used in the wood shop.  This condition exposed the employees to an electrical hazard.    Note: Relocatable power taps are intended to be directly connected to a permanently installed branch circuit receptacle. Relocatable power taps are not intended to be series connected (daisy chained) to other relocatable power taps or to extension cords.   Relocatable power taps are not intended to use at construction sites and similar locations. Relocatable power taps are not intended to be permanently secured to building structures, tables, work benches or similar structures, nor are they to be used as a substitute for fixed wiring of the structure. The cords of relocatable power taps are not intended to be routed through walls, windows, ceiling, floors or similar openings. Relocatable power taps are intended for indoor use to power laboratory equipment, home workshops, home movie lighting controls, musical instrumentation, and to provide outlet receptacles for computers, audio and video equipment, and other equipment.    Abatement Note:  Abatement certification is required for this item (see enclosed "Certification of Corrective Action Worksheet").