OSHA Inspection: JESS BRILEY MANUFACTURING COMPANY

Issued

2012-06-29 00:00:00

Abate by

2012-08-24 00:00:00

Penalty

Initial $4900.00 · Current $2940.00 Reduced

General-duty citation text

29 CFR 1910.147(c)(1):     The employer did not establish a program consisting of an energy control procedure, employee training and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative:      The employer does not ensure an energy control program for machines consisting of energy control procedures, employee training and periodic inspections is established.   This violation occurred on or about May 11, 2012 at the workplace where employees were exposed to struck-by and caught-in hazards when conducting servicing and maintenance activities on, but not limited to, the following machines and equipment with but not limited to, electrical, pneumatic, and hydraulic energy sources without an energy control program.      Location 6, standard modern,106997,polishing lathe,220/3 phase, compressed air 125 psi  Location 7,	standard modern,106997,polishing lathe,220/3 phase, compressed air 125 psi  Locatoin 8,	standard modern,106997,polishing lathe,220/3 phase, compressed air 125 psi  Location 9,	 atrump machinery,b5fc,lathe,220/3 phase, compressed air, hydraulic 350 psi   Location 10, standard modern,106997,polishing lathe,220/3 phase, compressed air 125 psi  Location 11, standard modern,106997,polishing lathe,220/3 phase, compressed air 125 psi  Location 19, mori seiki,	sl-1a, CNC Lathe,220/3 phase, hydraulic 350 psi  Location 20, mori seiki,	sl-15, CNC Lathe,220/3 phase, hydraulic 350 psi  Location 21,mori seiki,	sl-15, CNC Lathe,220/3 phase, hydraulic 350 psi  Location 22, mori seiki,	sl-15, CNC Lathe,220/3 phase, hydraulic 350 psi  Location 23,mori seiki,	sl-150, CNC Lathe,220/3 phase, compressed air 125 psi, hydraulic 350 psi  Location 24,mori seiki,	sl-15, CNC Lathe,220/3 phase, hydraulic 350 psi  Location 25,mori seiki,	sl-15, CNC Lathe, 220/3 phase, Hydraulic 350 psi  Location 26, hass, vf3ss, CNC Mill, 	220/3 phase, compressed air 125 psi, hydraulic 350 psi  Location 28,fadal engineering, 904-20, CNC Mill, 220/3 phase, compressed air 125 psi, hydraulic  350 psi  Location 29, mori seiki,	mv40, CNC Mill,220/3 phase, compressed air 125 psi, hydraulic 350 psi  Location 30, fadal engineering,906-1, CNC Mill,	220/3 phase, compressed air 125 psi, hydraulic 350 psi  Location 31, mori seiki, frontier-m2	, CNC Mill,220/3 phase, compressed air 125 psi, hydraulic 350 psi  Location 32, revolution machine technology, Mill,220/3 phase, compressed air 125 psi, hydraulic 350 psi  Location 33, mazak, variaxis 500-5xII, 220/3 phase, compressed air 125 psi, hydraulic 350 psi  Location 35, mori seiki,	sl-150, CNC Lathe,220/3 phase, compressed air 125 psi, hydraulic 350 psi  Location 36, mori seiki,	sl-a, CNC Lathe, 220/3 phase, hydraulic 350 psi  Location 37, mori seiki,	sl-150, CNC Lathe,220/3 phase, compressed air 125 psi, hydraulic 350 psi  Location 38, mori seiki, sl-15, CNC Lathe, 220/3 phase, hydraulic 350 psi  Location 39, mori seiki, zt1000y, CNC Lathe,220/3 phase, compressed air 125 psi, hydraulic 350 psi  Location 40,mori seiki,	sl-150, CNC Lathe,220/3 phase, compressed air 125 psi, hydraulic 350 psi  Location 41, mori seiki,	sl-15, CNC Lathe, 220/3 phase, hydraulic 350 psi  Location 42, mori seiki, sl-15, CNC Lathe,220/3 phase, hydraulic 350 psi  Location 44, sunnen, 2y1-1065, 220/3 phase, compressed air 125 psi, hydraulic 350 psi  Location 45, powermatic,87, Band Saw,220/3 phase, hydraulic 350 psi

Issued

2012-06-29 00:00:00

Abate by

2012-08-24 00:00:00

Penalty

Initial $4900.00 · Current $2940.00 Reduced

General-duty citation text

29 CFR 1910.212(a)(1):  One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips, and sparks:    The employer does not ensure that rotating parts of machines are guarded exposing employees to struck-by hazards.  The following violations of this occurred on or about May 11, 2012, in the production area where employees were exposed to struck-by hazards when operating lathes with rotating chucks without a guard.    a) Location 2, Nardini, Model ND1560e, Lathe	  b) Location 3, Standard Modern, Model 13/40, Lathe	  c) Location 6, Standard Modern, Model 106997, Polishing Lathe   d) Location 7, Standard Modern, Model 106997, Polishing Lathe   e) Location 8, Standard Modern, Model 106997, Polishing Lathe  f) Location 9, Atrump Machinery, Model B5FC, Lathe	  g) Location 10, Standard Modern, Model 106997, Polishing Lathe	  h) Location 11, Standard Modern, Model 106997, Polishing Lathe	  i) Location 12, Sharp, Model 1340, Lathe	  j) Location 13, Clausing, Lathe	  k) Location 14, Standard Modern, Lathe	  l) Location 15, Clausing, Lathe	  m) Location 16, Standard Modern, Model 1340, Lathe	  n) Location 17, Nardini, Model MS1440e, Lathe	  o) Location 18, Hass, Model TI-1, Lathe	  p) Location 43, Clausing, Model Hl-1500-d, CNC Lathe   q) Location 46, Emco Maler, Model Maximat V1 Lathe

Issued

2012-06-29 00:00:00

Abate by

2012-07-09 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.305(b)(1)(ii): Unused openings in boxes, cabinets, or fittings were not effectively closed:    The employer does not ensure that unused opening in electrical circuit breakers were effectively closed.  This violation was observed on or about May 11, 2012, in Panel N, CNC Production Area where unused openings were not effectively closed and protected.