Safety Incidents OSHA Severe Injury Reports · 2015–2025
2,004,209Inspections Most recent open 2026-07-13 Last loaded 2026-07-17

OSHA Inspection: FORREST MACHINE PRODUCTS CO. LTD.

Planned inspection · Safety discipline

On , OSHA opened a planned safety inspection of FORREST MACHINE PRODUCTS CO. LTD. in 139 SOUTH ILLINOIS, MANSFIELD, OH 44905 (NAICS 332710). OSHA activity number 337286819.

Watch Forrest Machine Products CO. LTD. — free Get an email when a new federal OSHA severe-injury report for Forrest Machine Products CO. LTD. is published. One employer, no account, unsubscribe in one click.
Site address
139 SOUTH ILLINOIS
City
MANSFIELD
State
OH
ZIP
44905
Mailing
139 SOUTH ILLINOIS, MANSFIELD, OH 44905
Inspection type
Planned (H)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
332710
Employees
29
Ownership type
A

3 citations on file for this inspection.

1910.147 C01

Serious Gravity 5 1 instance 4 exposed
Issued
Abate by
Penalty
Initial $3500.00 · Current $2450.00 Reduced
29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure, employee training and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative:    a)  Forrest Machine Products, Inc. located on 139 South Illinois Avenue in Mansfield, Ohio: On or about January 9, 2013, the employer failed to develop and implement an energy control plan along with procedures and training to protect employees from injuries while they engaged in servicing and maintenance activities on equipment such as, but not limited to, the Doosan Turning Center.
Recent events (2)
  • — I (S) $2450
  • — Z (S) $3500

1910.212 A01

Serious Gravity 5 1 instance 1 exposed
Issued
Abate by
Penalty
Initial $2800.00 · Current $1960.00 Reduced
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks:    a) Forrest Machine Products, Inc. located on 139 South Illinois Avenue in Mansfield, Ohio: On or about January 9, 2013, the employer failed to properly guard several Brown & Sharp screw machines and prevent caught-in hazards created by the rotating drive shaft hand wheel.
Recent events (2)
  • — I (S) $1960
  • — Z (S) $2800

1910.219 E04

Serious Gravity 5 1 instance 1 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $0.00
29 CFR 1910.219(e)(4): Vertical belts. Vertical belts running over a lower pulley more than seven (7) feet above floor or platform shall be guarded at the bottom in the same manner as horizontal overhead belts, if conditions are as stated in paragraphs (e)(2)(ii) (a) and (c) of this section.    a) Forrest Machine Products, Inc. located on 139 South Illinois Avenue in Mansfield, Ohio: On or about Jan 9, 2013, the employer did not fully guard vertical belts on the several Brown & Sharp screw machines and exposed an employee a rotating vertical drive belt.
Recent events (2)
  • — I (S) $0
  • — Z (S) $0

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 337286819.