OSHA Inspection: JOHN P. GAUDET INC.

Issued

2013-06-26 00:00:00

Abate by

2013-07-02 00:00:00

Penalty

Initial $2800.00 · Current $1960.00 Reduced

General-duty citation text

29 CFR 1926.501(b)(11): Each employee on a steep roof with unprotected sides and edges 6 feet (1.8 m) or more above lower levels was not protected from falling by guardrail systems with toeboards, safety net systems, or personal fall arrest systems:    At the Jobsite - The employees working at a height of 8 - 10 feet were not protected from falling by adequate fall protection.

Issued

2013-06-26 00:00:00

Abate by

2013-07-04 00:00:00

Penalty

Initial $2800.00 · Current $1960.00 Reduced

General-duty citation text

29 CFR 1926.304(f): Section 4.1.2(b) American National Standards Institute 01.1-1961, Safety Code for Woodworking Machinery as adopted by 29 CFR 1926.304(f):  Circular hand-fed ripsaws were not guarded by an automatically adjusting hood which completely encloses that portion of the saw above the table and above the material being cut:    At the Jobsite - The 8 inch Dewalt table saw was not provded with a hood guard.

Issued

2013-06-26 00:00:00

Abate by

2013-07-05 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1926.304(f): Section 4.1.2(b) American National Standards Institute 01.1-1961, Safety Code for Woodworking Machinery as adopted by 29 CFR 1926.304(f):  Circular hand-fed rip saws were not equipped with a spreader to prevent material from squeezing the saw or being thrown back on the operator:  At the Jobsite - The 8 inch Dewalt table saw was not provided with a spreader.

Issued

2013-06-26 00:00:00

Abate by

2013-07-03 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1926.304(f): Section 4.1.2(c) American National Standards Institute 01.1-1961, Safety Code for Woodworking Machinery as adopted by 29 CFR 1926.304(f):  Circular hand-fed rip saws did not have non-kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator:  At the Jobsite - The 8 inch Dewalt table saw was not provided with non-kickback fingers.

Issued

2013-06-26 00:00:00

Abate by

2013-07-04 00:00:00

Penalty

Initial $2000.00 · Current $0.00 Reduced

General-duty citation text

29 CFR 1926.304(f): Section 5.1.3.3 American National Standards Institute 01.1-1961, Safety Code for Woodworking Machinery as adopted by 29 CFR 1926.304(f):  Electrically driven equipment was not controlled with magnetic switches or other devices that would prevent automatic restarting of the machine after a power failure:    At the Jobsite - The electrically driven 8 inch Dewalt table saw was not provided with anti-restart protection.

Issued

2013-06-26 00:00:00

Abate by

2013-07-02 00:00:00

Penalty

Initial $1600.00 · Current $1120.00 Reduced

General-duty citation text

29 CFR 1926.1053(b)(1): Portable ladders were used for access to an upper landing surface and the ladder side rails did not extend at least 3 feet (.9 m) above the upper landing surface to which the ladder was used to gain access:    At the Jobsite - The ladder did not extend 3 feet above the landing surface.

Issued

2013-06-26 00:00:00

Abate by

2013-07-02 00:00:00

Penalty

Initial $2000.00 · Current $0.00 Reduced

General-duty citation text

29 CFR 1926.1053(b)(13): The top or top step of a stepladder was used as a step:    At the Jobsite - The top step of a stepladder was used as a step.