OSHA Inspection: SX INVESTMENT GROUP INCORPORATED

Issued

2013-08-12 00:00:00

Abate by

2013-10-01 00:00:00

Penalty

Initial $1200.00 · Current $500.00 Reduced

General-duty citation text

29 CFR 1910.23(c)(1): Open-sided floors and/or platforms four feet or more above adjacent floor or ground level were not guarded with standard railings (or equivalent) and toeboards:Note:  Toeboards are only required when persons can pass, there is moving equipment or there is equipment with which falling materials could create a hazard.    Shipping Dept.:         One section of the platform near the lift did not have a guardrail.

Issued

2013-08-12 00:00:00

Abate by

2013-10-01 00:00:00

Penalty

Initial $2000.00 · Current $900.00 Reduced

General-duty citation text

29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure, employee training and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative:(a)    Worksite:           The employer did not develop a written lockout tagout program. The company has power presses. The company has lathes.

Issued

2013-08-12 00:00:00

Abate by

2013-10-01 00:00:00

Penalty

Initial $1600.00 · Current $700.00 Reduced

General-duty citation text

29 CFR 1910.178(l)(1)(i): The employer did not ensure that each powered industrial truck operator is competent to operate a powered industrial truck safely, as demonstrated by the successful completion of the training and evaluation specified in this paragraph (l):    Worksite:        The employer did not train the operators of powered industrial trucks on the safety rules for operating the trucks.

Issued

2013-08-12 00:00:00

Abate by

2013-10-01 00:00:00

Penalty

Initial $1200.00 · Current $600.00 Reduced

General-duty citation text

29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks:    Tool and Diemaking Room:           The rotating shaft and end nut of the buffing wheel were not guarded.

Issued

2013-08-12 00:00:00

Abate by

2013-10-01 00:00:00

Penalty

Initial $2800.00 · Current $2100.00 Reduced

General-duty citation text

29 CFR 1910.215(b)(9): The distance between the abrasive wheel periphery(s) and the adjustable tongue or the end of the safety guard peripheral member at the top exceeded one fourth inch:    Tool and Diemaking Shop:               The bench grinder was not equipped with tongue guards at both wheels. A worker was injured when a cutoff wheel shattered and struck his face.

Issued

2013-08-12 00:00:00

Abate by

2013-10-01 00:00:00

Penalty

Initial $1600.00 · Current $700.00 Reduced

General-duty citation text

29 CFR 1910.242(b): Compressed air used for cleaning purposes was not reduced to less than 30 p.s.i.:    Tool and Diemaking Room:           The dead end pressure of an air hose exceeded 30 PSI.

Issued

2013-08-12 00:00:00

Abate by

2013-10-01 00:00:00

Penalty

Initial $400.00 · Current $0.00 Reduced

General-duty citation text

29 CFR 1904.29(a): Basic requirement. You must use OSHA 300, 300-A, and 301 forms, or equivalent forms, for recordable injuries and illnesses. The OSHA 300 form is called the Log of Work-Related Injuries and Illnesses, the 300-A is the Summary of Work-Related Injuries and Illnesses, and the OSHA 301 form is called the Injury and Illness Incident Report.    Worksite:     1)         The employer did not maintain an OSHA 300 injury and illness log.     2)          The employer did not maintain OSHA 301 forms for each injury.

Issued

2013-08-12 00:00:00

Abate by

2013-10-01 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.303(g)(2)(i): Except as elsewhere required or permitted by Subpart S of Part 1910, live parts of electric equipment operating  at 50 volts or more were not guarded against accidental contact by use of approved cabinets or other forms of approved enclosures:  Tool and Diemaking:            All outlet boxes were not covered.