Safety Incidents OSHA Severe Injury Reports · 2015–2025
4,113,118Inspections Most recent open 2026-07-13 Last loaded 2026-07-17

OSHA Inspection: DONE RIGHT CONSTRUCTION INC.

Referral inspection · Safety discipline

On , OSHA opened a referral safety inspection of DONE RIGHT CONSTRUCTION INC. in 1201 NE MONROE ST., PEORIA, IL 61603 (NAICS 562910). OSHA activity number 339228058.

Watch Done Right Construction INC. — free Get an email when a new federal OSHA severe-injury report for Done Right Construction INC. is published. One employer, no account, unsubscribe in one click.
Site address
1201 NE MONROE ST.
City
PEORIA
State
IL
ZIP
61603
Mailing
2997 S LYMAN, CHICAGO, IL 60608
Inspection type
Referral (C)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
562910
Employees
7
Ownership type
A

7 citations on file for this inspection.

1926.404 B01 I

Serious Gravity 5 1 instance 1 exposed
Issued
Abate by
Penalty
Initial $1600.00 · Current $1100.00 Reduced
29 CFR 1926.404(b)(1)(i): Employer did not use either ground fault circuit interrupters as specified in paragraph (b)(1)(ii) of this section, or an assured equipment grounding conductor program as specified in paragraph (b)(1)(iii) of this section to protect employees on construction sites.    An employee was exposed to electrical shock and burn hazards while using a Milwaukee circular saw which was plugged into a extension cord powered by a power receptacle which was not protected through the usage of a ground fault circuit interrupter or assurred equipment ground program.
Recent events (3)
  • — F (S) $1100
  • — C (S) $1600
  • — Z (S) $1600

1926.404 B01 III C

Serious Gravity 5 1 instance 1 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $0.00
29 CFR 1926.404(b)(1)(iii)(C): Where an assured equipment grounding conductor program was being utilized, the employer did not ensure that each cord set, attachment cap, plug and receptacle of cord sets, and any equipment connected by cord and plug, except cord sets and receptacles which are fixed and not exposed to damage, were not visually inspected fofore each day's use for external defects, such as deformed or missing pins or insulation damage, and for indications of possible internal damage.  An employee was exposed to electrical shock and burn hazards while using a Milwaukee circular saw which was plugged into a extension cord which had been cut by the saw and had a missing ground prong.
Recent events (3)
  • — F (S) $0
  • — C (S) $0
  • — Z (S) $0

1926.405 G02 III

Serious Gravity 5 1 instance 1 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $0.00
29 CFR 1926.405(g)(2)(iii): Flexible cords were not used in continuous lengths without splice or tap:  An employee was exposed to electrical shock and burn hazards while using a Milwaukee circular saw which was plugged into a extension cord which had been spliced.
Recent events (3)
  • — F (S) $0
  • — C (S) $0
  • — Z (S) $0

1926.452 K01

Serious Gravity 1 1 instance 1 exposed
Issued
Abate by
Penalty
Initial $1200.00 · Current $900.00 Reduced
29 CFR 1926.452(k)(1): Platforms exceeded a height of 20 feet (6.1 m)    An employee was exposed to struck by hazards in the event of a fall while working from an ladder jack scaffold.  The scaffold was approximately 25 feet high.
Recent events (3)
  • — F (S) $900
  • — C (S) $1200
  • — Z (S) $1200

1926.20 B01

Serious Gravity 5 1 instance 1 exposed
Issued
Abate by
Penalty
Initial $2000.00 · Current $2000.00
29 CFR 1926.20(b)(1): The employer did not initiate and maintain accident prevention programs as necessary to comply with this part:    An employee was exposed to a fall hazard while performing cleanup operations because the employer did not have an effective safety and health program with specific work rules, competent person oversight, and employee training to govern employee's activity.
Recent events (3)
  • — F (S) $2000
  • — C (S) $2000
  • — Z (S) $2000

1926.20 B02

Serious Gravity 5 1 instance 1 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $0.00
29 CFR 1926.20(b)(2): The employer did not initiate and maintain a safety program which provides for frequent and regular inspections of jobsites, materials, and equipment to be made by a competent person:    An employee was exposed to a fall hazard while performing cleanup operations because the employer did not have a competent person at the site conducting frequent and periodic safety inspections of hte construction site.
Recent events (3)
  • — F (S) $0
  • — C (S) $0
  • — Z (S) $0

1926.501 B01

Serious Gravity 10 1 instance 1 exposed
Issued
Abate by
Penalty
Initial $2800.00 · Current $0.00 Reduced
29 CFR 1926.501(b)(1): Each employee on a walking/working surface with an unprotected side or edge which was 6 feet (1.8 m) or more above a lower level was not protected from falling by the use of guardrail systems, safety net systems, or personal fall arrest systems.    An employee was exposed to a fall hazard of approximately 17 feet while performing cleanup operations on top of the lower roof and the employer did not ensure the employee was protected from fall hazards through the usage of fall protection.
Recent events (3)
  • — F (S) $0
  • — C (S) $2800
  • — Z (S) $2800

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339228058.