OSHA Inspection: JAY DIFULVIO & ASSOCIATES INC.

Issued

2013-11-27 00:00:00

Penalty

Initial $1600.00 · Current $1120.00 Reduced

General-duty citation text

29 CFR 1926.304(f): Section 4.1.2(b) American National Standards Institute 01.1-1961, Safety Code for Woodworking Machinery as adopted by 29 CFR 1926.304(f): Electrically driven equipment was not equipped with magnetic switches or other devices that will prevent automatic restarting of the machine after a power failure:     a) 539 South Salina Street - On or about 25 October, 2013 - Employees were using a table saw to rip wood that did not have an anti restart device on the table saw.

Issued

2013-11-27 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1926.304(h)(1): Each circular crosscut table saw was not guarded by a hood which completely enclosed that portion of the saw blade above the table and that portion of the saw above the material being cut:  a) 539 South Salina Street - On or about 25 October, 2013- Employees were using a table saw to cut wood that was not guarded by a hood which enclosing the saw blade above the table.

Issued

2013-11-27 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1926.304(f): Section 4.1.2(b) American National Standards Institute 01.1-1961, Safety Code for Woodworking Machinery as adopted by 29 CFR 1926.304(f): Circular hand-fed rip saws were not equipped with a spreader to prevent material from squeezing the saw or being thrown back on the operator:  a) 539 South Salina Street - On or about 25 October, 2013- Employees were using a table saw to rip wood that did not have a spreader installed on the table saw.

Issued

2013-11-27 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1926.304(f): Section 4.1.2(c) American National Standards Institute 01.1-1961, Safety Code for Woodworking Machinery as adopted by 29 CFR 1926.304(f): Circular hand-fed rip saws did not have non-kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator:  a) 539 South Salina Street - On or about 25 October, 2013 - Employees were using a table saw to rip wood that did not have non-kickback fingers installed on the table saw.

Issued

2013-11-27 00:00:00

Abate by

2013-12-10 00:00:00

Penalty

Initial $1200.00 · Current $840.00 Reduced

General-duty citation text

29 CFR 1926.404(f)(6): The path to ground from circuits, equipment, or enclosures was not permanent and continuous:  a) 539 South Salina Street - On or about 25 October, 2013 - Employees were using extensions cords to power tools that did not have the ground prong.

Issued

2013-11-27 00:00:00

Abate by

2013-12-10 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1926.404(b)(1)(ii): On a construction site, where an assured equipment grounding program was not utilized, all 120-volt, single-phase, 15 and 20 ampere receptacle outlets which were not a part of the permanent wiring of the building or structure and which are in use by employees did not have approved ground fault circuit interrupters for personal protection.   a) 539 South Salina Street - On or about 25 October, 2013 - Employees were using extension cords to power tools that were not protected by a ground fault circuit interrupter.

Issued

2013-11-27 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1926.405(g)(1)(iii)(B): Flexible cords and cables were run through holes in walls, ceilings, or floors:  a) 539 South Salina Street - On or about 25 October, 2013 - Employees were using flexible cords that were run through a hole in the floor.

Issued

2013-11-27 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1926.405(g)(2)(iv): Flexible cords were not connected to devices and fittings so that strain relief is provided to prevent pull from being directly transmitted to joints or terminal screws:  a) 539 South Salina Street - On or about 25 October, 2013- Employees were using a table saw that was missing the strain relief on the plug.