Safety Incidents OSHA Severe Injury Reports · 2015–2025
2,004,209Inspections Most recent open 2026-07-13 Last loaded 2026-07-17

OSHA Inspection: FORMED FIBER TECHNOLOGIES, LLC

Complaint inspection · Safety discipline

On , OSHA opened a complaint safety inspection of FORMED FIBER TECHNOLOGIES, LLC in 260 STOLLE AVE., SIDNEY, OH 45365 (NAICS 336360). OSHA activity number 339803108.

Watch Formed Fiber Technologies, LLC — free Get an email when a new federal OSHA severe-injury report for Formed Fiber Technologies, LLC is published. One employer, no account, unsubscribe in one click.
Site address
260 STOLLE AVE.
City
SIDNEY
State
OH
ZIP
45365
Mailing
260 STOLLE AVN., SIDNEY, OH 45365
Inspection type
Complaint (B)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
336360
Employees
50
Ownership type
A

3 citations on file for this inspection.

1910.147 C06 I

Willful Gravity 10 1 instance 20 exposed
Issued
Abate by
Penalty
Initial $70000.00 · Current $38436.00 Reduced
29 CFR 1910.147(c)(6)(i): The employer did not conduct a periodic inspection of the energy control procedure at least annually to ensure that the procedure and the requirement of this standard were being followed:    a)      On or about June 11, 2014, the employer did not conduct annual audits of its energy control procedures to assure that proper lockout/tagout procedures and requirements were being followed.  Lack of procedure audits exposed employees to injuries when employees accessed hazard areas of machines while performing mold changes on the trim presses.
Recent events (3)
  • — F (W) $38436
  • — C (W) $70000
  • — Z (W) $70000

1910.147 D

Willful Gravity 10 1 instance 20 exposed
Issued
Abate by
Penalty
Initial $70000.00 · Current $38436.00 Reduced
29 CFR 1910.147(d): The established procedure for the application of energy control (the lockout or tagout procedures) did not cover the actions listed in and was not done in sequence as required by 29 CFR 1910.147(d)(1)-(6):     a) On or about June 11, 2014, employees were exposed to crushing injuries while the Pinette trim presses on lines 3, 4 and 5 were not locked out prior to performing mold changes.  Prior to accessing the hazard areas of the machine to perform these tasks the employer failed to implement energy control application steps as required by paragraph (d) of this section  - the employer did not:            *    Ensure that equipment was turned off or shut down.          *    Physically operate energy isolating devices to control energy sources and affix lockout device(s).          *    Ensure that all potentially hazardous stored or residual energy was relieved, disconnected, and rendered safe.          *    Verify that isolation and deenergiziation of the machine or equipment had been accomplished.
Recent events (3)
  • — F (W) $38436
  • — C (W) $70000
  • — Z (W) $70000

1910.132 D02

Other-than-serious 1 instance 50 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $0.00
29 CFR 1910.132(d)(2): The employer did not verify, through a written certification, that the required workplace hazard assessment had been performed:   a)    On or about June 11, 2014 the employer did not certify that a hazard assessment was performed to address the chemical and physical hazards found in the workplace.
Recent events (3)
  • — F (O) $0
  • — C (O) $0
  • — Z (O) $0

View FORMED FIBER TECHNOLOGIES, LLC's full OSHA safety record →

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339803108.