Safety Incidents OSHA Severe Injury Reports · 2015–2025
5,189,214Inspections Most recent open 2026-07-16 Last loaded 2026-07-20

OSHA Inspection: MEISNER ELECTRIC, INC. DBA MEISNER SERVICES

Unprogrammed Other inspection · Safety discipline

On , OSHA opened an unprogrammed Other safety inspection of MEISNER ELECTRIC, INC. DBA MEISNER SERVICES in 2051 BEVIN DR., ALLENTOWN, PA 18104 (NAICS 238220). OSHA activity number 340139914.

Watch Meisner Electric, INC. DBA Meisner Services — free Get an email when a new federal OSHA severe-injury report for Meisner Electric, INC. DBA Meisner Services is published. One employer, no account, unsubscribe in one click.
Site address
2051 BEVIN DR.
City
ALLENTOWN
State
PA
ZIP
18104
Mailing
958 N. PENN ST., ALLENTOWN, PA 18102
Inspection type
Unprogrammed Other (I)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
238220
Employees
20
Ownership type
A

3 citations on file for this inspection.

1926.502 B01

Serious Gravity 5 1 instance 20 exposed
Issued
Penalty
Initial $1445.00 · Current $1951.00
29 CFR 1926.502(b)(1): The top edge height of the top rails, or equivalent guardrail system members, was not 42 inches (1.1 m) plus or minus 3 inches (8 cm) above the walking/working level:Note:  When employees are using stilts, the top edge height of the top rail, or equivalent member, shall be increased an amount equal to the height of the stilts.    a) 2051 Bevin Dr. Allentown, Pa., 1st Level, Elevator shaft - On or about December 12, 2014, employees were performing mechanical installation throughout a two-story commercial structure, while being exposed to an inadequately guarded elevator shaft opening, in that the top rail height was approximately 30 inches above the floor height, which created a fall hazard from 14 feet above a lower level.
Recent events (2)
  • — I (S) $1950.75
  • — Z (S) $1445

1926.502 B03

Serious Gravity 5 1 instance 3 exposed
Issued
Penalty
Initial $0.00 · Current $0.00
29 CFR 1926.502(b)(3): Guardrail systems were not capable of withstanding, without failure, a force of at least 200 pounds (890 N) applied within 2 inches (5.1 cm) of the top edge, in any outward or downward direction, at any point along the top edge:  a) 2051 Bevin Dr. Allentown, Pa., 1st Level, Elevator shaft - On or about December 12, 2014, employees were performing mechanical installation throughout a two-story commercial structure, while being exposed to an inadequately guarded elevator shaft opening, the guardrail would displace under minimal hand pressure, which created a fall hazard from 14 feet above a lower level.
Recent events (2)
  • — I (S) $0
  • — Z (S) $0

1926.502 B13

Serious Gravity 5 1 instance 3 exposed
Issued
Penalty
Initial $1156.00 · Current $0.00 Reduced
29 CFR 1926.502(b)(13): When guardrail systems were used around holes which were used as access (such as ladderways), they were not provided with a gate, or were not so offset that a person could not walk directly into the hole:    a) 2051 Bevin Dr. Allentown, Pa., Mezzanine Area - On or about December 12, 2014, employees were performing mechanical installation in the mezzanine where a floor opening used for ladder access, approximately 10 feet above the lower level, was not guarded by a standard guardrail or equivalent.
Recent events (2)
  • — I (S) $0
  • — Z (S) $1156

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 340139914.