Safety Incidents OSHA Severe Injury Reports · 2015–2025
4,113,118Inspections Most recent open 2026-07-13 Last loaded 2026-07-17

OSHA Inspection: JOHN R. DUDLY CONSTRUCTION CO. INC.

Planned inspection · Safety discipline

On , OSHA opened a planned safety inspection of JOHN R. DUDLY CONSTRUCTION CO. INC. in OCWA, 4170 ROUTE 31, CLAY, NY 13041 (NAICS 238990). OSHA activity number 340564541.

Watch John R. Dudly Construction CO. INC. — free Get an email when a new federal OSHA severe-injury report for John R. Dudly Construction CO. INC. is published. One employer, no account, unsubscribe in one click.
Site address
OCWA, 4170 ROUTE 31
City
CLAY
State
NY
ZIP
13041
Mailing
PO BOX 306, 5848 STATE ROUTE 104, OSWEGO, NY 13126
Inspection type
Planned (H)
Scope
Complete (A)
Discipline
Safety
Advance notice
No
Union status
A
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
238990
Employees
4
Ownership type
A

3 citations on file for this inspection.

1910.134 D01 III

Serious Gravity 1 1 instance 1 exposed
Issued
Abate by
Penalty
Initial $1200.00 · Current $900.00 Reduced
29 CFR 1910.134(d)(1)(iii): The employer did not identify and evaluate the respiratory hazard(s) in the workplace; including a reasonable estimate of employee exposures to respiratory hazards and identification of the contaminant's chemical state and physical form. (As referenced in CFR 1926.103):  a) At the jobsite, on or about 4/14/15:  A worker was using an air hammer to abrade and remove the surface from several sections of concrete sidewalk and driveway without wearing a respirator, and without the employer having conducted an assessment to determine the need for respiratory protection where the likelihood of exposure to silica was likely.    Abatement certification must be submitted for this item.
Recent events (2)
  • — I (S) $900
  • — Z (S) $1200

1926.502 B03

Other-than-serious 1 instance 7 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $0.00
29 CFR 1926.502(b)(3): Guardrail systems were not capable of withstanding, without failure, a force of at least 200 pounds (890 N) applied within 2 inches (5.1 cm) of the top edge, in any outward or downward direction, at any point along the top edge:  a) At the jobsite, on the roof, on or about 4/14/15:  Workers were performing roofing work on an irregularly shaped roof where a cable guardrail system was installed at the direction of the contractor, and where that cable system was incorrectly installed and not able to assure the 200 pound minimum force requirement.    Abatement certification must be submitted for this item.
Recent events (2)
  • — I (O) $0
  • — Z (O) $0

1926.503 A02 II

Other-than-serious 1 instance 7 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $0.00
29 CFR 1926.503(a)(2)(ii): The employer did not assure that each employee, as necessary, had been trained by a competent person in the correct procedures for erecting, maintaining, disassembling and inspecting the fall protection systems to be used:  a) At the jobsite, on the roof, on or about 4/14/15:  Workers were performing roofing work on an irregularly shaped roof where a cable guardrail system was installed at the direction of the contractor, and where that cable system was incorrectly installed not able to assure the 200 pound minimum force requirement, nor were workers trained to recognize the faulty installation.    Abatement certification must be submitted for this item.
Recent events (2)
  • — I (O) $0
  • — Z (O) $0

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 340564541.