OSHA Inspection: MASTERPIECE GRAPHIX INC.

Issued

2015-06-19 00:00:00

Abate by

2015-08-06 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.147(c)(1):  The employer did not establish a program consisting of energy control procedures, employee training, and periodic inspections to ensure that before any employee performs any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment would be isolated from the energy source and rendered inoperative:  Inside of the Production Area, a lockout/tagout program was not developed or documented for the following machines that utilize 220 volts and 38 p.s.i. pneumatic energy sources:  a/  Roll Coating Machine #1.  b/  Roll Coating Machine #2.  c/  Roll Coating Machine #3.  d/  Roll Coating Machine #4.  e/  Roll Coating Machine #5.  f/   Sheet Roller Coater #6.  g/  Sheet Roller Coater #7.

Issued

2015-06-19 00:00:00

Abate by

2015-08-06 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.147(c)(4)(i):  Procedures were not developed, documented, and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section:  Inside of the Production Area, a specific procedure was not developed or documented for the following machines that utilize 220 volts and 38 p.s.i. pneumatic energy sources:  a/  Roll Coating Machine #1.  b/  Roll Coating Machine #2.  c/  Roll Coating Machine #3.  d/  Roll Coating Machine #4.  e/  Roll Coating Machine #5.  f/   Sheet Roller Coater #6.  g/  Sheet Roller Coater #7.

Issued

2015-06-19 00:00:00

Abate by

2015-08-06 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.147(c)(5)(i): Locks, tags, chains, wedges, key blocks, adapter pins, self-locking fasteners, or other hardware were not provided by the employer for isolating, securing or blocking of machines or equipment from energy sources:  Inside of the Production Area, lockout/tagout devices were neither provided nor used for the following machines that utilize 220 volts and 38 p.s.i. pneumatic energy sources:  a/  Roll Coating Machine #1.  b/  Roll Coating Machine #2.  c/  Roll Coating Machine #3.  d/  Roll Coating Machine #4.  e/  Roll Coating Machine #5.  f/   Sheet Roller Coater #6.  g/  Sheet Roller Coater #7.

Issued

2015-06-19 00:00:00

Abate by

2015-08-06 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.147(c)(7)(i)(A): Each authorized employee did not receive training in the recognition of applicable hazardous energy sources, the type and magnitude of the energy available in the workplace, and the methods and means necessary for energy isolation and control:  Inside of the Production Area, "authorized" employee(s) were not instructed to use lockout/tagout devices to isolate the 220 volts and 38 p.s.i. pneumatic energy sources belonging to the following machines:  a/  Roll Coating Machine #1.  b/  Roll Coating Machine #2.  c/  Roll Coating Machine #3.  d/  Roll Coating Machine #4.  e/  Roll Coating Machine #5.  f/   Sheet Roller Coater #6.  g/  Sheet Roller Coater #7.