OSHA Inspection: ZIG'S HEATING AND COOLING

Issued

2015-09-10 00:00:00

Penalty

Initial $1360.00 · Current $680.00 Reduced

General-duty citation text

29 CFR 1910.37(a)(3): Exit route(s) were not kept free and unobstructed:    (a) An exit route, located on the north wall near the western side of the building, was not kept free of debris and material.

Issued

2015-09-10 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.36(d)(1): Employee(s) were not able to open an exit route door from the inside at all times without keys, tools, or special knowledge:  (a) An exit door, located on the north wall near the western side of the building, was locked and secured with cable that prevented immediate use of the door.

Issued

2015-09-10 00:00:00

Abate by

2015-10-06 00:00:00

Penalty

Initial $2000.00 · Current $1000.00 Reduced

General-duty citation text

29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks:    (a) The employer did not ensure that the Flagler roll forming machine was guarded.

Issued

2015-09-10 00:00:00

Abate by

2015-10-06 00:00:00

Penalty

Initial $1200.00 · Current $600.00 Reduced

General-duty citation text

29 CFR 1910.303(c)(3)(i): All splices and joints and the free ends of the conductors were not covered with an insulation equivalent to that of the conductors or with an insulating device identified for the purpose.      (a) The employer did not ensure that electrical cords of differing types, that powered an S & Drive roll forming machine in the shop area, were spliced with a proper insulating device.

Issued

2015-09-10 00:00:00

Abate by

2015-10-06 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.303(b)(2): Listed or labeled electrical equipment was not used or installed in accordance with instructions included in the listing or labeling:  (a) The employer did not ensure that the S & Drive machine was installed in accordance with proper listing and labeling methods.

Issued

2015-09-10 00:00:00

Penalty

Initial $1360.00 · Current $680.00 Reduced

General-duty citation text

29 CFR 1910.303(g)(1)(i)(A): For electric equipment operating at 600 volts, nominal, or less to ground, and likely to require examination, adjustment, servicing, or maintenance while energized, the depth of the working space in the direction of access to live parts (as measured from the live parts where they were exposed or from the enclosure front or opening whwere they were enclosed) was less than indicated in Table S-1 of Subpart S of Part 1910:    (a) The employer did not ensure that the clearance depth was maintained in front of an electrical panel on the north wall in the shop area.

Issued

2015-09-10 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.303(g)(1)(i)(B): For electric equipment operating at 600 volts, nominal, or less to ground, and likely to require examination, adjustment, servicing, or maintenance while energized, the width of the working space in front of electrical equipment was less than the width of the equipment or 762 mm (30 inches), whichever was greater :  (a) The employer did not ensure that the clearance width was maintained in front of an electrical panel on the north wall in the shop area.

Issued

2015-09-10 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.22(a)(1): All places of employment, passageways, storerooms or service rooms were not kept clean and orderly or in a sanitary condition.  (a) The employer did not ensure that the shop area was kept in a clean and orderly condition.