OSHA Inspection: STANDARD FUSEE CORPORATION

Issued

2016-04-21 00:00:00

Abate by

2016-05-06 00:00:00

Penalty

Initial $3060.00 · Current $3000.00 Reduced

General-duty citation text

29 CFR 1910.119(e)(1): The employer did not perform an initial process hazard analysis (hazard evaluation) on processes covered by 29 CFR 1910.119:    a) Standard Fusee Corporation, - On or about December 16, 2015, the employer operated a Process Safety Management (PSM) covered explosive pyrotechnic manufacturing process, without a Process Hazard Analysis (PHA) completed for the process that included these operations.

Issued

2016-04-21 00:00:00

Abate by

2016-05-06 00:00:00

Penalty

Initial $3825.00 · Current $3000.00 Reduced

General-duty citation text

29 CFR 1910.219(f)(3): Sprocket wheels and chains which were seven (7) feet or less above floors or platforms were not enclosed:    a) Standard Fusee Corporation, Charging Room - On or about February 12, 2016, the sprocket wheels and chain of the charging / loading machine were not guarded to prevent injuries to employees.

Issued

2016-04-21 00:00:00

Abate by

2016-05-06 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.119(f)(3): The employer did not annually certify that operating procedures were current and accurate.  a) Standard Fusee Corporation, - On or about December 16, 2015, the employer did not certify that their SOP-01BR Emergency Evacuation Plan was current and accurate since October 30, 2008.    b) Standard Fusee Corporation, - On or about December 16, 2015, the employer did not certify that their SOP-08BR restriction on Smoking & Open Lights was current and accurate since October 30, 2008.    c) Standard Fusee Corporation, - On or about December 16, 2015, the employer did not certify that their SOP-39BR Hazardous Communication Program was current and accurate since October 30, 2008.    d) Standard Fusee Corporation, - On or about December 16, 2015, the employer did not certify that their SOP-110BR Orange Smoke Signal Assembly was current and accurate since October 30, 2008.

Issued

2016-04-21 00:00:00

Abate by

2016-05-06 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.119(f)(4): The employer did not develop and implement safe work practices to provide for the control of hazards during operations such as lockout/tagout; confined space entry; opening process equipment or piping; and control over entrance into a facility by maintenance, contractor, laboratory, or other support personnel:  a) Standard Fusee Corporation, Charging Room - On or about December 16, 2015, the employer did not develop and implement safe work practices to provide for the control of hazards during operations such as lockout/tagout and control over entrance into a facility by maintenance, or other support personnel.

Issued

2016-04-21 00:00:00

Abate by

2016-05-06 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.147(c)(6)(i): The employer did not conduct a periodic inspection of the energy control procedure at least annually to ensure that the procedure and the requirement of this standard were being followed:  a) Standard Fusee Corporation, Charging Room - On or about December 16, 2015, the employer did not conduct a periodic inspection of their energy control procedure since on October, 2008 to ensure that the procedure and the requirement of the OSHA standards were being followed.

Issued

2016-04-21 00:00:00

Abate by

2016-05-06 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.303(b)(2): Listed or labeled electrical equipment was not used or installed in accordance with instructions included in the listing or labeling:  a) Standard Fusee Corporation, - On or about February 12, 2016, a Romex brand nonmetallic-sheathed cable being used to supply power to a DC controller and a Rockwell brand floor standing drill press, was not installed in accordance with instructions included in the listing or labeling.  ABTEMENT NOTE: Among other methods, one feasible and acceptable means of abatement is to follow the instructions and guidelines of Article 334 of ANSI/NFPA 70, "National Electrical Code" and the Underwriters Laboratory White Book information.

Issued

2016-04-21 00:00:00

Abate by

2016-05-06 00:00:00

Penalty

Initial $2295.00 · Current $0.00 Reduced

General-duty citation text

29 CFR 1910.1200(f)(6): The employer did not ensure that each container of hazardous chemicals in the workplace was labeled, tagged or marked with the information specified under paragraphs (f)(6)(i) through (ii) of this section:     a) Standard Fusee Corporation, - On or about February 12, 2016, did not ensure that each container of their Wick Paint primer mixture was labeled, tagged or marked with the information specified under paragraphs (f)(6)(i) through (ii).      b) Standard Fusee Corporation, - On or about February 12, 2016, did not ensure that each container of their Button Paint mixture was labeled, tagged or marked with the information specified under paragraphs (f)(6)(i) through (ii).

Issued

2016-04-21 00:00:00

Abate by

2016-05-06 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.1200(g)(2): The chemical manufacturer or importer preparing the safety data sheet did not ensure that it included the required headings and information in 29 CFR 1910.1200(g)(2)(i) through 29 CFR 1910.1200(g)(2)(xii)    a) Standard Fusee Corporation, - On or about February 12, 2016, the employer who manufactures their Wick Paint primer  chemical on site did not ensure that a Safety Data Sheet was developed and used with all the required information for that mixture as required.       b) Standard Fusee Corporation, - On or about February 12, 2016, the employer who manufactures their Button Paint mixture chemical on site did not ensure that a Safety Data Sheet was developed and used with all the required information for that mixture as required.