OSHA Inspection: FORM-ALL SPRING & STAMPING COMPANY, INC.

Issued

2018-06-06 00:00:00

Abate by

2019-05-01 00:00:00

Penalty

Initial $3696.00 · Current $1848.00 Reduced

General-duty citation text

29 CFR 1910.212(a)(3)(ii): Point(s) of operation of machinery were not guarded to prevent employee(s) from having any part of their body in the danger zone(s) during operating cycle(s):    Employees operating the following Torsion Spring Winder, Vertislides, and 4-Slide machines were exposed to amputation hazards when the point(s) of operation of the machines were not guarded to prevent employees from having any part of their body in the danger zones during the operating cycle:    a.  Torrington Torsion Spring Winder Serial # 108482TM  b.  Torrington Torsion Spring Winder Serial # 10638  c.  Torrington Torsion Spring Winder Serial # 92878  d.  1st #5P Latour Vertislide  e.  2nd #5P Latour Verislide  f.  S4F Nilson 4-Slide  g.  1st S4 Nilson 4-Slide  h.  2nd S4 Nilson 4-Slide  i.  S3F Nilson 4-Slide  j.  RWI 4-Slide  k.  1st #1 Baird 4-Slide  l.  2nd #1 Baird 4-Slide  m  #00 Baird 4-Slide    Abatement documentation is required of this item in accordance with the requirements in 29 CFR 1903.19(d).

Issued

2018-06-06 00:00:00

Abate by

2018-12-03 00:00:00

Penalty

Initial $3696.00 · Current $1848.00 Reduced

General-duty citation text

29 CFR 1910.219(b)(2): Crank(s) or connecting rod(s) exposed to contact were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o) or by guardrail(s) as described in CFR 1910.219(o)(5):    Employees operating the following Torrington Spring Winders, were exposed to laceration, fraction and amputation hazards due to unguarded connecting rods located on the sides of the machines:    a.  Torrington Torsion Spring Winder, Serial # 108482 TM  b.  Torrington Torsion Spring Winder, Serial # 10638  c.  Torrington Torsion Spring Winder, Serial # 92878    Abatement documentation is required of this item in accordance with the requirements of 29 CFR 1903.19(d).

Issued

2018-06-06 00:00:00

Abate by

2018-08-13 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.219(c)(2)(i): All exposed part(s) of horizontal shafting seven (7) feet or less from floor or working platform were not protected by stationary casing(s) enclosing shafting completely or by trough(s) enclosing sides and top or sides and bottom of shafting:    Employees operating the following Torrington Torsion Spring Winders, were exposed to laceration, fracture, and amputation hazards as a result of unguarded horizontal shafts located less than seven feet from the floor:    a.  Torrington Torsion Spring Winder, Serial # 108482TM  b.  Torrington Torsion Spring Winder, Serial # 10638  c.  Torrington Torsion Spring Winder, Serial # 92878    Abatement documentation is required of this item in accordance of the requirements of 29 CFR 1903.19(d).

Issued

2018-06-06 00:00:00

Abate by

2018-12-03 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.219(f)(1): Gear(s) were not guarded by a complete enclosure or by one of the methods specified in 29 CFR 1910.219(f)(1)(ii) and (f)(1)(iii):  Employees, operating the following Torrington Torsion Spring Winders, were exposed to laceration, fraction, and amputation hazards due to the machines not being guarded.  The gears were not located at least 6 feet from the floor.  a.  Torrington Torsion Spring Winder, Serial # 108482TM b.  Torrington Torsion Spring Winder, Serial # 10638 c.  Torrington Torsion Spring Winder, Serial # 92878.   Abatement certification of this item is required in accordance with the requirements of 29 CFR 1903.19(d).

Issued

2018-06-06 00:00:00

Abate by

2018-07-13 00:00:00

Penalty

Initial $2956.00 · Current $1478.00 Reduced

General-duty citation text

29 CFR 1910.243(a)(3): Portable belt sanding machine(s) were not guarded at each nip point where the sanding belt runs onto the pulley(s):    The portable belt sanding machine in the Tool Room was not guarded at each nip point where the sanding belt runs onto the pulley.  The employees were exposed to laceration hazards.    Abatement documentation is required of this item in accordance with the requirements of 29 CFR 1903.19(d).