Safety Incidents OSHA Severe Injury Reports · 2015–2025
4,113,118Inspections Most recent open 2026-07-13 Last loaded 2026-07-17

OSHA Inspection: DYNEGY ILLINOIS, INC.

Planned inspection · Health discipline

On , OSHA opened a planned health inspection of DYNEGY ILLINOIS, INC. in 199 ILLINOIS 104, KINCAID, IL 62540 (NAICS 221112). OSHA activity number 343053682.

Watch Dynegy Illinois, INC. — free Get an email when a new federal OSHA severe-injury report for Dynegy Illinois, INC. is published. One employer, no account, unsubscribe in one click.
Site address
199 ILLINOIS 104
City
KINCAID
State
IL
ZIP
62540
Mailing
PO BOX 260, KINCAID, IL 62540
Inspection type
Planned (H)
Scope
Partial (B)
Discipline
Health
Advance notice
No
Union status
A
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
221112
Employees
140
Ownership type
A

5 citations on file for this inspection.

1910.146 C02

Deleted Serious Gravity 5 1 instance 140 exposed
Issued
Abate by
Penalty
Initial $7391.00 · Current $0.00 Reduced
29 CFR 1910.146(c)(2): The employer did not inform exposed employees, by posting danger signs or by any other equally effective means, of the existence and location of and the danger posed by permit spaces.  On or about March 27, 2018, employees were exposed to potentially hazardous atmospheres present by the permit spaces accessible through the 14-cyclone hatchways and the employer did not post danger signs (or have other equally effective means) to  inform employees on the danger posed by the permit spaces.
Recent events (3)
  • — F (S) $0
  • — C (S) $7391
  • — Z (S) $7391

1910.219 C02 I

Serious Gravity 5 1 instance 140 exposed
Issued
Abate by
Penalty
Initial $7391.00 · Current $7436.00
29 CFR 1910.219(c)(2)(i): All exposed part(s) of horizontal shafting seven (7) feet or less from floor or working platform were not protected by stationary casing(s) enclosing shafting completely or by trough(s) enclosing sides and top or sides and bottom of shafting:    On or about March 27, 2018, employees were exposed to contact with an unprotected rotating shaft and the shaft was not protected by an enclosure at the following equipment:    a) Conveyor 5B (ramp side); and    b) Crusher 1B (West).
Recent events (3)
  • — F (S) $7436
  • — C (S) $7391
  • — Z (S) $7391

1910.219 C04 I

Deleted Serious Gravity 5 1 instance 140 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $0.00
29 CFR 1910.219(c)(4)(i): Shaft ends projecting more than one-half the diameter of the shaft were not guarded by nonrotating caps or safety sleeves.  On or about March 27, 2018, employees were exposed to contact with unprotected rotating shafts and the shafts were not protected by caps or safety sleeves at the following equipment:  a) Conveyor Line 5B (ramp side);  b) Conveyor Line 5B (stair side); and  c) Feeder 5B2.
Recent events (3)
  • — F (S) $0
  • — C (S) $0
  • — Z (S) $0

1910.307 B

Deleted Serious Gravity 5 1 instance 140 exposed
Issued
Abate by
Penalty
Initial $7391.00 · Current $0.00 Reduced
29 CFR 1910.307(b): Documentation for areas designated as hazardous (classified) locations under the Class and Zone system and areas designated under the Class and Division system established after August 13, 2007 was not available to those authorized to design, install, inspect, maintain, or operate electric equipment at the location:  On or about March 27, 2018, employees installed, inspected, and maintained electric equipment in hazardous locations and the employer did not document the boundaries of each division or zone in the form of drawings that visually depict the boundaries or in text that precisely describes the extent of each hazardous location.
Recent events (3)
  • — F (S) $0
  • — C (S) $7391
  • — Z (S) $7391

1910.307 C

Serious Gravity 5 1 instance 140 exposed
Issued
Penalty
Initial $0.00 · Current $7436.00
29 CFR 1910.307(c): Equipment, wiring methods, and installations of equipment in hazardous (classified) locations were not intrinsically safe, approved for the hazardous (classified) location, or safe for the hazardous (classified) location:    On or about March 27, 2018, employees were exposed to smoke inhalation and burn hazards (combustible PRB coal dust) and the employer provided electrical equipment that was not safe for the hazardous (classified) location including:    a) condulet plug missing near Feeder 6A; and     b) unsecured condulet cover at the stairway landing of Conveyor 5B.
Recent events (3)
  • — F (S) $7436
  • — C (S) $0
  • — Z (S) $0

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 343053682.