Safety Incidents OSHA Severe Injury Reports · 2015–2025
5,189,214Inspections Most recent open 2026-07-16 Last loaded 2026-07-20

OSHA Inspection: METRIC & MULTISTANDARD COMPONENTS CORP.

Complaint inspection · Safety discipline

On , OSHA opened a complaint safety inspection of METRIC & MULTISTANDARD COMPONENTS CORP. in 261 SHORE COURT, BURR RIDGE, IL 60527 (NAICS 493110). OSHA activity number 346742471.

Watch Metric & Multistandard Components Corp. — free Get an email when a new federal OSHA severe-injury report for Metric & Multistandard Components Corp. is published. One employer, no account, unsubscribe in one click.
Site address
261 SHORE COURT
City
BURR RIDGE
State
IL
ZIP
60527
Mailing
261 SHORE COURT, BURR RIDGE, IL 60527
Inspection type
Complaint (B)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
493110
Employees
20
Ownership type
A

4 citations on file for this inspection.

1910.37 A03

Serious Gravity 5 1 instance 4 exposed
Issued
Abate by
Penalty
Initial $4465.00 · Current $2236.00 Reduced
29 CFR  1910.37(a)(3): Exit routes must be free and unobstructed.  No materials or equipment may be placed, either permanently or temporarily, within the exit route.  The exit access must not go through a room that can be locked, such as a bathroom, to reach an exit or exit discharge, nor may it lead into a dead-end corridor.  Stairs or a ramp must be provided where the exit route is not substantially level.   On or about May 02, 2023, the exit doors were obstructed by boxes.  Employees were exposed to fire hazards due to obstructed egress.  Certification of abatement is required for this item in accordance with the requirements of 29 CFR 1903.19(c).
Recent events (2)
  • — I (S) $2236
  • — Z (S) $4465

1910.133 A01

Serious Gravity 1 1 instance 4 exposed
Issued
Abate by
Penalty
Initial $2678.00 · Current $1339.00 Reduced
29 CFR  1910.133(a)(1): The employer shall ensure that each affected employee uses appropriate eye or face protection when exposed to eye or face hazards from flying particles, molten metal, liquid chemicals, acids or caustic liquids, chemical gases or vapors, or potentially injurious light radiation.  On or about May 02, 2023, the employer did not ensure that employees were provided eye protection while using a bandsaw to cut metal rods thus exposing the employees to potential eye injuries from metal particulates.  Certification of abatement is required for this item in accordance with the requirements of 29 CFR 1903.19(c).
Recent events (2)
  • — I (S) $1339
  • — Z (S) $2678

1910.178 L01 I

Serious Gravity 5 1 instance 4 exposed
Issued
Abate by
Penalty
Initial $3572.00 · Current $1786.00 Reduced
29 CFR  1910.178(l)(1)(i): The employer shall ensure that each powered industrial truck operator is competent to operate a powered industrial truck safely, as demonstrated by the successful completion of the training and evaluation specified in this paragraph (l).  On or about May 02, 2023, the employer did not ensure that each powered industrial truck operator had been trained and was competent to operate a powered industrial truck such as a forklift safely.  Employees are exposed to struck-by hazards.  Abatement documentation is required for this item in accordance with the requirements of 29 CFR 1903.19(d).
Recent events (2)
  • — I (S) $1786
  • — Z (S) $3572

1910.1200 E01

Serious Gravity 1 1 instance 4 exposed
Issued
Abate by
Penalty
Initial $2678.00 · Current $1339.00 Reduced
29 CFR  1910.1200(e)(1): Employer had not developed or implemented a written hazard communication program including  requirements outlined in 29 CFR 1910.1200(e)(1)(i) and (e)(1)(ii):    On or about May, 2023, the employer did not develop and implement a hazardous communication program for employees who work with hazardous chemicals such as Zep and WD-40.  Employees routinely use Zep and WD-40 to remove rust from bolts.    Abatement documentation is required for this item in accordance with the requirements of 29 CFR 1903.19(d).
Recent events (2)
  • — I (S) $1339
  • — Z (S) $2678

View METRIC & MULTISTANDARD COMPONENTS CORP.'s full OSHA safety record →

SPEEDX

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 346742471.