Safety Incidents OSHA Severe Injury Reports · 2015–2025
4,113,118Inspections Most recent open 2026-07-13 Last loaded 2026-07-17

BOW, NH —

OSHA Inspection: EASTERN METAL FRAMING OF NH, LLC

Complaint inspection · Safety discipline

At a glance

On , OSHA opened a complaint safety inspection of EASTERN METAL FRAMING OF NH, LLC in 4 TALLWOOD DRIVE, BOW, NH 03304 (NAICS 332311). OSHA activity number 347871469.

Watch Eastern Metal Framing OF NH, LLC — free Get an email when a new federal OSHA severe-injury report for Eastern Metal Framing OF NH, LLC is published. One employer, no account, unsubscribe in one click.

Where did this inspection happen?

Establishment
EASTERN METAL FRAMING OF NH, LLC
Site address
4 TALLWOOD DRIVE
City
BOW
State
NH
ZIP
03304
Mailing
4 OLD NASHUA ROAD, LONDONDERRY, NH 03053

What kind of inspection was it?

Inspection type
Complaint (B)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
B

When did the case open and close?

Opened
Closing conference
Last modified
Data loaded

Establishment context

NAICS code
332311
Employees
30
Ownership type
A

Citations

3 citations on file for this inspection.

1910.22 A01

Other-than-serious Gravity 5 2 instances 20 exposed
Issued
Abate by
Penalty
Initial $6620.00 · Current $2000.00 Reduced

General-duty citation text

29 CFR  1910.22(a)(1): 29 CFR 1910.22(a)(1): The employer did not ensure that all places of employment, passageways, storerooms, service rooms, and walking-working surfaces are kept in a clean, orderly, and sanitary condition.   a. Line 3 - On or about November 12, 2024, employees were exposed to trip/fall hazards due to cords laying on the floor. b. Line 1 - On or about November 12, 2024, employees were exposed to trip/fall hazards due to cords laying on the floor. c. Line 2 - On or about November 12, 2024, employees were exposed to trip/fall hazards due to cords laying on the floor and a printer cord located above the walking-working surface. d. Line 4 - On or about November 12, 2024, employees were exposed to trip/fall hazards due to cords laying on the floor.
Recent events (2)
  • — I (O) $2000
  • — Z (S) $6620

1910.212 A03 II

Serious Gravity 5 12 instances 30 exposed
Issued
Abate by
Penalty
Initial $8276.00 · Current $4138.00 Reduced

General-duty citation text

29 CFR  1910.212(a)(3)(ii):  Point(s) of operation of machinery were not guarded to prevent employee(s) from having any part of their body in the danger zone(s) during operating cycle(s):   a. Line 3 - On or about November 8, 2024, employees working near the B&K 3 TSR Supermill were exposed to crushing/amputation hazards.  The shear was not effectively guarded. b. Line 1 - On or about November 8, 2024, employees working near the B&K DWR Supermill were exposed to crushing/amputation hazards.  The shear was not effectively guarded. c. Line 1 - On or about November 8, 2024, employees working near the B&K DWR Supermill were exposed to being struck by metal studs exiting the roll-former.  d. Line 2 - On or about November 8, 2024, employees working near the Dahlstrom rollforming machine were exposed to being struck by metal studs exiting the roll-former and cutting block. e. Line 2 - On or about November 8, 2024, employees working near the Dahlstrom rollforming machine were exposed to crushing/pinching hazards.  The moving cutting block was not effectively guarded. f. Line 4 - On or about November 12, 2024, employees working near the B&K DWR Supermill were exposed to crushing/amputation hazards.  The shear was not effectively guarded. g. Line 4 - On or about November 12, 2024, employees working near the B&K DWR Supermill were exposed to being struck by metal studs exiting the roll-former.  h. Line 4 - On or about November 12, 2024, employees working near the B&K coil handler (uncoiler) were exposed to being struck by or caught by moving components of the uncoiler.   i. Cut-to-length Line - On or about November 12, 2024, employees working near the shop made cutting shear were exposed to amputation/crushing hazards.  j. Cut-to-length Line - On or about November 12, 2024, employees working near the Mecon Industries coil handler (uncoiler) were exposed to being struck by or caught by moving components of the uncoiler.   k. Accessory Line - On or about November 12, 2024, employees working near the Tekfab machine were exposed to amputation/crushing hazards.  The rollforming wheels were not effectively guarded. l. Accessory Line - On or about November 12, 2024, employees working near the coil handler (uncoiler) were exposed to being struck by or caught by moving components of the uncoiler.
Recent events (2)
  • — I (S) $4138
  • — Z (S) $8276

1910.303 B02

Other-than-serious 2 instances 20 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $0.00

General-duty citation text

29 CFR  1910.303(b)(2): Listed or labeled electrical equipment was not used or installed in accordance with instructions included in the listing or labeling:  a. Line 4 - On or about November 12, 2024, a relocatable power tap was plugged into an extension cord.  The cord was used to power electronic equipment.
Recent events (2)
  • — I (O) $0
  • — Z (O) $0

More inspections in this industry (NAICS 332311)

More inspections in NH

Source

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 347871469.