Safety Incidents OSHA Severe Injury Reports · 2015–2025
3,913,242Inspections Most recent open 2026-07-13 Last loaded 2026-07-17

OSHA Inspection: TROPIC TOOL & MOLD, INC.

Planned inspection · Health discipline

On , OSHA opened a planned health inspection of TROPIC TOOL & MOLD, INC. in 1420 WAGNER DRIVE, ALBERTVILLE, AL 35950 (NAICS 333515). OSHA activity number 334177037.

Watch Tropic Tool & Mold, INC. — free Get an email when a new federal OSHA severe-injury report for Tropic Tool & Mold, INC. is published. One employer, no account, unsubscribe in one click.
Site address
1420 WAGNER DRIVE
City
ALBERTVILLE
State
AL
ZIP
35950
Mailing
1420 WAGNER DRIVE, ALBERTVILLE, AL 35950
Inspection type
Planned (H)
Scope
Partial (B)
Discipline
Health
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
333515
Employees
13
Ownership type
A

4 citations on file for this inspection.

5(a)(1)

Serious Gravity 5 1 instance 6 exposed
Issued
Penalty
Initial $2400.00 · Current $1440.00 Reduced
OSH ACT of 1970 Section (5)(a)(1):     The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to crushed by and struck-by hazards:      a)   On or about 5/3/12 - Manufacturing area, a Caterpillar forklift, Model MC30, Serial #4HB1196, was operated without a seatbelt.     Among other methods, one feasible and acceptable method to correct this hazard is to ensure that seatbelts are provided and utilized in accordance with ASME B.56.1b-2003, Safety Standard for Low Lift and High Lift Trucks, Section 7.41, Operator Restraint Systems.
Recent events (2)
  • — I (S) $1440
  • — Z (S) $2400

5(a)(1)

Serious Gravity 5 2 instances 4 exposed
Issued
Penalty
Initial $2000.00 · Current $1200.00 Reduced
OSH ACT of 1970 Section (5)(a)(1):     Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which was free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to struck-by hazards:       a)    On or about 05/03/12 - Assembly table #1, a Lynx 1 ton chain operated hoist, Model #HH1A, was being operated without a safety latch.    b)    On or about 05/03/12 - Assembly table #2, a CM series hoist,  Model #622, was being operated without a safety latch.
Recent events (2)
  • — I (S) $1200
  • — Z (S) $2000

1910.23 E01

Serious Gravity 1 1 instance 2 exposed
Issued
Penalty
Initial $1200.00 · Current $720.00 Reduced
29 CFR 1910.23(e)(1):     The railing did not consist of top rail, intermediate rail, and posts, and did not have a vertical height of 42 inches nominal from upper surface of top rail to floor, platform, runway, or ramp level:      a)   On or about 05/03/12 - Storage area, a stairway railing leading up to the storage room did not have a midrail.
Recent events (2)
  • — I (S) $720
  • — Z (S) $1200

1910.178 L04 III

Other-than-serious 1 instance 5 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $0.00
29 CFR 1910.178(l)(4)(iii):     An evaluation of each powered industrial truck operator's performance was not being conducted at least once every three years:     a)  On or about 06/19/12 - Assembly and loading areas, employees operating the Caterpillar forklift had not been evaluated as required.
Recent events (2)
  • — I (O) $0
  • — Z (O) $0

View TROPIC TOOL & MOLD, INC.'s full OSHA safety record →

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 334177037.