OSHA Inspection: TRAIL MANOR MANUFACTURING CO, LLC

Issued

2015-08-19 00:00:00

Abate by

2016-01-21 00:00:00

Penalty

Initial $2000.00 · Current $500.00 Reduced

General-duty citation text

29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure and employee training to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energizing, start up or release of stored energy could occur and cause injury, the machine or equipment would be isolated, and rendered inoperative in accordance with 29 CFR 1910.147(c)(4):                                                             56251 Hwy 84, Hartington, NE 68739 (Site-Wide):  There was no energy control program provided by the employer that met the requirements of 1910.147, including but not limited to;       a)     Authorized employees servicing equipment,  b)     Non-authorized employees whose work operations may be in a area where energy control procedures are being utilized and;  c)     Outside contractors engaged in activities covered by this standard.      Abatement certification and abatement documentation is required for this violation. The abatement certification sheet is enclosed with the citations.

Issued

2015-08-19 00:00:00

Abate by

2016-01-21 00:00:00

Penalty

Initial $1200.00 · Current $500.00 Reduced

General-duty citation text

29 CFR 1910.178(l)(4)(iii): An evaluation of each powered industrial truck operators performance shall be conducted at least once every three years:      56251 Hwy 84, Hartington, NE 68739 (Site-Wide): The employer is failing to ensure that employees performances were being evaluated at least once every three years prior to operating a forklift.      Abatement certification is required for this violation.  Abatement certification sheet is enclosed with the citation.

Issued

2015-08-19 00:00:00

Abate by

2016-01-21 00:00:00

Penalty

Initial $1600.00 · Current $500.00 Reduced

General-duty citation text

29 CFR 1910.215(b)(9):  The distance between the abrasive wheel periphery(s) and the adjustable tongue or the end of the safety guard peripheral member at the top exceeded one fourth inch:                                                                                                          56251 Hwy 84, Hartington, NE 68739 (Routing): The employer is failing to ensure a tongue guard on the Craftsman 8 bench grinder was adjusted to a 1/4 inch opening. The distance between the abrasive wheel periphery(s) and the adjustable tongue or the end of the safety guard peripheral member at the top opening was 1 inch.      Abatement certification is required for this violation.  Abatement certification sheet is enclosed with the citation.

Issued

2015-08-19 00:00:00

Abate by

2016-01-21 00:00:00

Penalty

Initial $1600.00 · Current $500.00 Reduced

General-duty citation text

29 CFR 1910.303(b)(2):  Listed or labeled electrical equipment was not used or installed in accordance with instructions included in the listing or labeling:      9555 S. 147th Street, Omaha, NE 68138 (West Shop, West Wall): The employer is failing to ensure that employees were not using listed or labeled equipment as intended.  An electrical box, which was intended for use while permanently fixed to a wall and which had pre-punched knockouts, was attached to the end of a flexible cord and was used to power a Dewalt Miter Saw.      Abatement certification is required for this violation.  Abatement certification sheet is enclosed with the citation.

Issued

2015-08-19 00:00:00

Abate by

2016-01-21 00:00:00

Penalty

Initial $1600.00 · Current $500.00 Reduced

General-duty citation text

29 CFR 1910.305(b)(2)(i): Each outlet box in completed installations did not have a cover, faceplate, or fixture canopy:      56251 Hwy 84, Hartington, NE 68739 (Routing): The employer is failing to ensure that an electrical cover was provided on an electrical junction box.      Abatement certification is required for this violation.  The abatement certification sheet is enclosed with the citation.

Issued

2015-08-19 00:00:00

Abate by

2016-01-21 00:00:00

Penalty

Initial $1600.00 · Current $500.00 Reduced

General-duty citation text

29 CFR 1910.305(g)(1)(iv): Flexible cords and cables were used for purposes prohibited by subparagraph (A) of this paragraph  where the employer did not ensure that a flexible cord was not used as a substitute for the fixed wiring of a structure:        56251 Hwy 84, Hartington, NE 68739 (Panel Shop): The employer did not ensure that a miter saw was plugged into a fixed receptacle. The Dewalt Miter Saw was plugged into an extension cord that was plugged into a fixed receptacle.      Abatement certification is required for this violation.  Abatement certification sheet is enclosed with the citation.

Issued

2015-08-19 00:00:00

Abate by

2015-10-06 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1910.1200(e)(1): The employer did not develop, implement, and/or maintain at the workplace a written hazard communication program which describes how the criteria specified in 29 CFR 1910.1200(f), (g), and (h) will be met:    56251 Hwy 84, Hartington, NE 68739 (Site-Wide) - The employer is failing to ensure to develop or implement a written hazard communication program meeting the minimum requirements specified in this subpart.     Abatement certification is required for this violation. The abatement certification sheet is enclosed with this citation.