DALTON, GA ·
OSHA Inspection: COOK & INGLE CO., INC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of COOK & INGLE CO., INC. in 400 CHEROKEE ESTATE ROAD, DALTON, GA 30722 (NAICS 000000). OSHA activity number 102827896.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- COOK & INGLE CO., INC.
- Site address
- 400 CHEROKEE ESTATE ROAD
- City
- DALTON
- State
- GA
- ZIP
- 30722
- Mailing
- P.O. BOX 626, DALTON, GA 30722
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 3272
- Employees
- 155
- Ownership type
- A
- Industry flags
- Manufacturing safety.
Citations
35 citations on file for this inspection.
5(a)(1)
- Issued
- May 4, 1988
- Abate by
- May 7, 1988
- Penalty
- Initial $490 · Current $490
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to: a) The hazard of being struck by falling loads in that a wire rope sling attached to the hook of a P & H Omega 40 ton Crane Serial #51718 was connected to two stake pockets on the front of the Fontaine Trailer #PTW 12980 which was loaded with approximately 40,000 pounds of precast concrete in order to lift the trailer so that the Kenworth W900 Tractor #674625 could be coupled. On or about 4-19-88. Among other methods, one feasible and acceptable method to correct this hazard is to use slings and/or attachments that are secured to the load in a manner which ensures proper lifting capacity and control.
1910.23 C01
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
- Penalty
- Initial $280 · Current $280
1910.133 A01
- Issued
- May 4, 1988
- Abate by
- May 7, 1988
- Penalty
- Initial $280 · Current $280
1910.184 C09
- Issued
- May 4, 1988
- Abate by
- May 7, 1988
- Penalty
- Initial $490 · Current $490
1910.212 A01
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
- Penalty
- Initial $350 · Current $350
1910.212 A03 II
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
- Penalty
- Initial $350 · Current $350
1910.215 A02
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
- Penalty
- Initial $280 · Current $280
1910.215 A04
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.219 E03 I
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
- Penalty
- Initial $280 · Current $280
1910.219 E01 I
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.219 F01
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.243 C02
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
- Penalty
- Initial $280 · Current $280
1910.243 C03
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.304 F05 V
- Issued
- May 4, 1988
- Abate by
- May 18, 1988
- Penalty
- Initial $420 · Current $420
1904.5 A
- Issued
- May 4, 1988
- Abate by
- May 18, 1988
- Penalty
- Initial $140 · Current $140
1904.2 A
- Issued
- May 4, 1988
- Abate by
- May 18, 1988
1910.23 C02
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.24 H
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.106 E02 IVD
- Issued
- May 4, 1988
- Abate by
- May 18, 1988
1910.106 E06 II
- Issued
- May 4, 1988
- Abate by
- May 18, 1988
1910.179 G01 V
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.179 J02 II
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.179 M01
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.180 B02
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.180 D06
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.180 G01
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.180 I05 I
- Issued
- May 4, 1988
- Abate by
- May 18, 1988
1910.184 E01
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.184 E03 I
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.213 H04
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.242 B
- Issued
- May 4, 1988
- Abate by
- May 7, 1988
1910.252 B04 IXC
- Issued
- May 4, 1988
- Abate by
- May 18, 1988
1910.305 G01 I
- Issued
- May 4, 1988
- Abate by
- May 18, 1988
1910.1200 E01
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
1910.1200 H
- Issued
- May 4, 1988
- Abate by
- Jun 6, 1988
More inspections at Cook & Ingle CO., INC.
View Cook & Ingle CO., INC.'s full OSHA safety record →
More inspections in this industry (NAICS 000000)
More inspections in GA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 102827896.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.