NEW YORK, NY ·
OSHA Inspection: PARK TOWER MANAGEMENT LTD
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of PARK TOWER MANAGEMENT LTD in 65 EAST 55TH STREET, NEW YORK, NY 10022 (NAICS 000000). OSHA activity number 102907748.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- PARK TOWER MANAGEMENT LTD
- Site address
- 65 EAST 55TH STREET
- City
- NEW YORK
- State
- NY
- ZIP
- 10022
- Mailing
- 499 PARK AVUENE, NEW YORK, NY 10022
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Union (Y)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 6514
- Employees
- 7
- Ownership type
- Private (A)
Citations
6 citations on file for this inspection.
5(a)(1)
- Issued
- Jan 28, 1997
- Abate by
- Jan 31, 1997
- Penalty
- Initial $3,000 · Current $1,800 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to being struck due to uncontrolled movement of unit or falling from a height up to 39 feet: a)Site 65 East 55th Street:Employees using the Genie to install lights on tree were exposed to the hazard of uncontrolled movement of unit striking employee or employee falling from height of 39 feet due to not operating the Genie with all four outriggers in place and pads contacting ground as required by manufactures safe operating procedure manual, on or about 11/27/96. Abatement Note: Among other method, one feasible and accepted method to correct this hazard is to use the Genie as instructed by manufacture and required in ANSI A 92.3 1990 Section 8.8.ion
Recent events (2)
- · I (S) $1800.00
- · Z (S) $3000.00
5(a)(1)
- Issued
- Jan 28, 1997
- Abate by
- Jan 31, 1997
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to being struck due to uncontrolled movement of unit and falling from height of 39 feet: a)Site 65 East 55th Street: Employee was exposed to falling from height of 39 feet due to not being trained in the proper safe operating procedure for the Genie as required in the company manual and ANSI 92.3 1990, on or about 11/27/96. Abatement Note: Among other method, one feasible and accepted method to correct this hazard is to use the Genie as instructed by manufacture and train the employees as required in ANSI A 92.3 1990 Section 8.6.ion
Recent events (2)
- · I (S)
- · Z (S)
5(a)(1)
- Issued
- Jan 28, 1997
- Abate by
- Feb 24, 1997
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to being struck due to uncontrolled movement of unit and falling from height of 39 feet: a)Site 65 East 55th Street: Employer did not maintain records of employees training for each type of Elevating Aerial platforms as required in ANSI 92.3 1990 section 7.6.2 and records of the frequent and annual inspection performed by owner as required in ANSI 92.3 section 6.12.3 on or about 12/02/96. Abatement Note: Among other method, one feasible and accepted method to correct this hazard is to use the Genie as instructed by manufacture and train the employees as required in ANSI A 92.3 1990 Section 8.6., conduct inspection and retain written records as in ANSI 92.3 section 6.12.3 and 7.6.2.
Recent events (2)
- · I (S)
- · Z (S)
1904.2 A
- Issued
- Jan 28, 1997
- Abate by
- Jan 31, 1997
Recent events (2)
- · I (O)
- · Z (O)
1910.1200 E01
- Issued
- Jan 28, 1997
- Abate by
- Mar 17, 1997
Recent events (2)
- · I (O)
- · Z (O)
1910.1200 H01
- Issued
- Jan 28, 1997
- Abate by
- Feb 24, 1997
Recent events (2)
- · I (O)
- · Z (O)
More inspections in this industry (NAICS 000000)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 102907748.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.