CHARM, OH ·
OSHA Inspection: G AND H DRILLING CO.
Accident-driven inspection · Safety discipline
At a glance
On , OSHA opened an accident-driven safety inspection of G AND H DRILLING CO. in COUNTY ROAD 600 CLARK TWP, CHARM, OH 44671 (NAICS 000000). OSHA activity number 103534491.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- G AND H DRILLING CO.
- Site address
- COUNTY ROAD 600 CLARK TWP
- City
- CHARM
- State
- OH
- ZIP
- 44671
- Mailing
- P.O. BOX 81, MT. HOPE, OH 44660
What kind of inspection was it?
- Inspection type
- Accident-driven (A)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 1381
- Employees
- 11
- Ownership type
- Private (A)
Citations
8 citations on file for this inspection.
5(a)(1)
- Issued
- Jan 17, 1990
- Abate by
- Feb 16, 1990
- Penalty
- Initial $700 · Current $700
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to: a) Rig #92 Mase Yoder Lease Well #1. Employees were subject to the hazards of being struck by and severly injured should a four inch inside diameter pressurized vibrator hose with an operating pressure of more than 200 psi gauge become disconnected and whip about striking them. Among other methods, one feasible and acceptable abatement method to correct his hazard is to secure the hose using chains properly located and of sufficient strength to resist hose whipping should it become disconnected or broken, as referenced in paragraph 8.14.3 of API-RP54 Recommended Practices for Occupational Safety and Health For Oil and Gas Well Drilling and Servicing Operations.
1910.151 B
- Issued
- Jan 17, 1990
- Abate by
- Mar 5, 1990
- Penalty
- Initial $500 · Current $500
1910.176 B
- Issued
- Jan 17, 1990
- Abate by
- Jan 26, 1990
- Penalty
- Initial $900 · Current $900
1910.1200 E01
- Issued
- Jan 17, 1990
- Abate by
- Feb 16, 1990
- Penalty
- Initial $400 · Current $400
1910.1200 G01
- Issued
- Jan 17, 1990
- Abate by
- Feb 16, 1990
- Penalty
- Initial $400 · Current $400
1910.1200 H
- Issued
- Jan 17, 1990
- Abate by
- Feb 16, 1990
- Penalty
- Initial $400 · Current $400
1904.4
- Issued
- Jan 17, 1990
- Abate by
- Feb 1, 1990
1904.2 A
- Issued
- Jan 17, 1990
- Abate by
- Feb 1, 1990
More inspections in this industry (NAICS 000000)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 103534491.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.