NEW BERLIN, WI ·
OSHA Inspection: ALLIED MANUFACTURING AND FABRICATING CO., INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of ALLIED MANUFACTURING AND FABRICATING CO., INC. in 13100 W. CLEVELAND AVE., NEW BERLIN, WI 53151 (NAICS 000000). OSHA activity number 103550810.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- ALLIED MANUFACTURING AND FABRICATING CO., INC.
- Site address
- 13100 W. CLEVELAND AVE.
- City
- NEW BERLIN
- State
- WI
- ZIP
- 53151
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 3469
- Employees
- 40
- Ownership type
- A
Citations
21 citations on file for this inspection.
5(a)(1)
- Issued
- Jun 14, 1989
- Abate by
- Jul 6, 1989
- Penalty
- Initial $200 · Current $60 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to: ANSI B30.20 1985 Title: Below the Hook Lifting Devices. Section 20-1.4.2 Rated Load Test. Prior to initial use, all new, altered, modified, or repaired lifting devices were not tested to insure compliance with this standard: a) Prior to initial use, the sheet grabber in the shear department, had not been tested under the direction of a qualified person and a written report furnished confirming the load rating of the lifter. Among other methods, one feasible and acceptable abatement method would be to follow the steps listed in ANSI B30.20-1985 Section 20-1.4.2 to obtain a rated load capacity for the lifter.
Recent events (2)
- · I (S) $60.00
- · Z (S) $200.00
1910.217 B07 III
- Issued
- Jun 14, 1989
- Abate by
- Aug 17, 1989
- Penalty
- Initial $240 · Current $60 Reduced
Recent events (2)
- · I (S) $60.00
- · Z (S) $240.00
1910.217 B07 IV
- Issued
- Jun 14, 1989
- Abate by
- Jul 17, 1989
1910.217 C05 I
- Issued
- Jun 14, 1989
- Abate by
- Aug 17, 1989
Recent events (2)
- · I (S)
- · Z (S)
1910.217 B06 I
- Issued
- Jun 14, 1989
- Abate by
- Jun 21, 1989
- Penalty
- Initial $200 · Current $60 Reduced
Recent events (2)
- · I (S) $60.00
- · Z (S) $200.00
1910.217 C03 VIID
- Issued
- Jun 14, 1989
- Abate by
- Jun 26, 1989
- Penalty
- Initial $200 · Current $60 Reduced
Recent events (2)
- · I (S) $60.00
- · Z (S) $200.00
1910.217 D09 IV
- Issued
- Jun 14, 1989
- Abate by
- Jul 3, 1989
- Penalty
- Initial $200 · Current $60 Reduced
Recent events (2)
- · I (S) $60.00
- · Z (S) $200.00
1910.217 B08 I
- Issued
- Jun 14, 1989
- Abate by
- Jul 3, 1989
1910.217 E01 I
- Issued
- Jun 14, 1989
- Abate by
- Jun 21, 1989
- Penalty
- Initial $160
Recent events (2)
- · I (O)
- · Z (S) $160.00
1910.305 B02
- Issued
- Jun 14, 1989
- Abate by
- Jun 21, 1989
- Penalty
- Initial $160 · Current $60 Reduced
Recent events (2)
- · I (S) $60.00
- · Z (S) $160.00
1910.304 F04
- Issued
- Jun 14, 1989
- Abate by
- Jun 21, 1989
1910.305 G01 I
- Issued
- Jun 14, 1989
- Abate by
- Jun 21, 1989
1910.305 G02 III
- Issued
- Jun 14, 1989
- Abate by
- Jun 21, 1989
1910.23 C01
- Issued
- Jun 14, 1989
- Abate by
- Jun 21, 1989
1910.212 A01
- Issued
- Jun 14, 1989
- Abate by
- Jun 21, 1989
1910.212 A03 II
- Issued
- Jun 14, 1989
- Abate by
- Jun 17, 1989
1910.217 G
- Issued
- Jun 14, 1989
- Abate by
- Jun 17, 1989
1910.1200 E01
- Issued
- Jun 14, 1989
- Abate by
- Sep 17, 1989
Recent events (2)
- · I (O)
- · Z (O)
1910.1200 F04 I
- Issued
- Jun 14, 1989
- Abate by
- Jul 17, 1989
1910.1200 G01
- Issued
- Jun 14, 1989
- Abate by
- Sep 17, 1989
Recent events (2)
- · I (O)
- · Z (O)
1910.1200 H
- Issued
- Jun 14, 1989
- Abate by
- Oct 1, 1989
Recent events (2)
- · I (O)
- · Z (O)
More inspections at Allied Manufacturing and Fabricating CO., INC.
View Allied Manufacturing and Fabricating CO., INC.'s full OSHA safety record →
More inspections in this industry (NAICS 000000)
More inspections in WI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 103550810.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.