LONGVIEW, TX ·
OSHA Inspection: PHOENIX TANK CO.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of PHOENIX TANK CO. in 6310 SOUTH LOOP 281, LONGVIEW, TX 75602 (NAICS 000000). OSHA activity number 109096461.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- PHOENIX TANK CO.
- Site address
- 6310 SOUTH LOOP 281
- City
- LONGVIEW
- State
- TX
- ZIP
- 75602
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (N)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 3443
- Employees
- 29
- Ownership type
- Private (A)
- Industry flags
- Manufacturing safety.
Citations
26 citations on file for this inspection.
5(a)(1)
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $1,000 · Current $1,000
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employmnent and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees when compressed air is transmitted through polyvinyl chloride (PVC) pipe, exposing employees to the hazard of being struck by flying fragments: a.Polyvinyl chloride PVC pipe was installed throughout the plant and used to transmit compressed air to machinery and hand held tools. Feasible abatement methods to correct this caondition may include but are not limited to, 1) enclosing the polyvinyl chloride (PVC) line in a conduit pipe of sufficient strength to provide protection from external damage and prevent employees from being struck by flying fragments; 2) install a pipe system designed for compressed air as recommended by the American National Standards Institute/American Society of Mechanical Engineers (ANSI/ASME) B 31.8-1986 sections 842.32,842.43 and 849.52 (b) Gas Transmission and Distribution Piping System.
1910.134 A02
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $1,000 · Current $1,000
1910.147 C01
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $1,000 · Current $1,000
1910.147 C04 I
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $1,000 · Current $1,000
1910.147 C05 I
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $1,000 · Current $1,000
1910.147 C07 I
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $1,000 · Current $1,000
1910.212 A03 II
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $1,400 · Current $1,400
1910.215 A02
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $600 · Current $600
1910.215 A04
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $600 · Current $600
1910.215 B09
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $600 · Current $600
1910.219 D01
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $2,000 · Current $2,000
1910.219 E03 I
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $2,000 · Current $2,000
1910.219 F03
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $2,000 · Current $2,000
1910.303 G02 I
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $2,000 · Current $2,000
1910.304 F05 V
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $1,000 · Current $1,000
1910.307 B
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $2,000 · Current $2,000
1910.1200 E01
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $1,000 · Current $1,000
1910.1200 H01 I
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
- Penalty
- Initial $1,000 · Current $1,000
1904.2 A
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
1910.22 A01
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
1910.132 D01
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
1910.132 F01
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
1910.179 G01 V
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
1910.179 I
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
1910.179 M01
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
1910.305 G02 II
- Issued
- Apr 19, 1995
- Abate by
- Jun 6, 1995
More inspections in this industry (NAICS 000000)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 109096461.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.