Safety Incidents OSHA Severe Injury Reports · 2015–2025
5,191,871Inspections Most recent open 2026-07-30 Last loaded 2026-08-03

OSHA Inspection: WINDOW BRITE WINDOW CLEANING CO

Referral inspection · Safety discipline

On , OSHA opened a referral safety inspection of WINDOW BRITE WINDOW CLEANING CO in WYOMING SEMINARY, N. SPRAGUE AVE., KINGSTON, PA 18704 (NAICS 000000). OSHA activity number 109367649.

What this inspection record means

OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.

Watch Window Brite Window Cleaning CO for free Get an email when a new federal OSHA severe-injury report for Window Brite Window Cleaning CO is published. One employer, no account, unsubscribe in one click.
Site address
WYOMING SEMINARY, N. SPRAGUE AVE.
City
KINGSTON
State
PA
ZIP
18704
Mailing
79 HUTSON STREET, WILKES-BARRE, PA 18702
Inspection type
Referral (C)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Data loaded
NAICS code
000000
SIC code (legacy)
7349
Employees
2
Ownership type
A

3 citations on file for this inspection.

5(a)(1)

Serious Gravity 05 1 instance 2 exposed
Issued
Oct 29, 1991
Abate by
Nov 3, 1991
Penalty
Initial $525 · Current $525
Section 5(a)(1) of the Occupational Safety and Health Act of 1970:  The
employer did not furnish employment and a place of employment which
were free from recognized hazards that were causing or likely to cause
death or serious physical harm to employees in that employees were
exposed to fall hazards:
(a)  Wyoming Seminary site - an employee was allowed
to work from a fiberglass ladder that was defective
in that a rubber pad was missing from the safety shoe
on one side rail and the fifth rung (from bottom) was
dented approximately one-half inch below the horizon-
tal.  In addition, the employee was allowed to work in
an unsafe manner, as the base of the ladder was only
38 inches from the building.  Employee was working from
the back side of the ladder and the ladder was not tied
or otherwise secured, on or about August 29, 1991.
Feasible and useful method of abatement:
The employer shall provide a training program for each
employee using ladders as necessary.  The program shall
enable each employee to recognize hazards related to
ladders and shall train each employee in the procedures
to be followed to minimize these hazards:
(1)   The employer shall ensure that each employee has
been trained by a competent person in the following
areas, as applicable:
(i)    The nature of fall hazards in the work area;
(ii)   The correct procedures for setting up a ladder
at the proper angle;
(iii)  The proper construction, use, placement and
care in handling of all ladders;
(iv)   The maximum intended load-carrying capacities
of ladders used;  and
(v)    Retraining shall be provided for each employee
as necessary so that the employee maintains the
understanding and knowledge acquired for compliance.
(2)   Ladders having defects are to be marked and taken
out of service until repaired by either maintenance
department or the manufacturer.

1910.1200 E01

Other-than-serious 1 instance 2 exposed
Issued
Oct 29, 1991
Abate by
Nov 12, 1991

1910.1200 H

Other-than-serious 1 instance 2 exposed
Issued
Oct 29, 1991
Abate by
Nov 12, 1991

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 109367649.

Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.