MILTON, FL ·
OSHA Inspection: TANGLEWOOD GOLF AND COUNTRY CLUB
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of TANGLEWOOD GOLF AND COUNTRY CLUB in 5916 TANGLEWOOD DRIVE, MILTON, FL 32570 (NAICS 000000). OSHA activity number 110137957.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- TANGLEWOOD GOLF AND COUNTRY CLUB
- Site address
- 5916 TANGLEWOOD DRIVE
- City
- MILTON
- State
- FL
- ZIP
- 32570
- Mailing
- P.O. BOX 725, MILTON, FL 32572
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (N)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 7992
- Employees
- 30
- Ownership type
- Private (A)
Citations
8 citations on file for this inspection.
5(a)(1)
- Issued
- Aug 5, 1997
- Abate by
- Aug 8, 1997
- Penalty
- Initial $750 · Current $750
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which was free from the hazard of being struck or punctured by projectiles from polyvinyl chloride (PVC) pipe. This hazard is likely to cause or likely cause death or serious physical harm to employees in that employees were exposed to the hazard of the pipe fragmenting or exploding. a.On or about May 22, 1997, the employer had a line pressure of 96 pounds per square inch (psi) used to transport compressed air for the pneumatic tools and spraying operations. Fragmentation of the pipe can occur because of fatigue cause by cold contents, and or ambient temperatures and non-compatibility of pipe with its contents, etc. Among other methods, 3 feasible means of abatement would be: 1. An Acrylonitrite, Butadiene Styrene (ABS) pipe could be used. 2. Polyvinyl vinyl chloride pipe (PVC) with that is completely enclosed in a conduit or casing of sufficient strength to provide protection from external damage and deterioration. 3. Metal piping could be used. ABATEMENT CERTIFICATION IS NOT REQUIRED.
1910.94 B05 II
- Issued
- Aug 5, 1997
- Abate by
- Aug 8, 1997
- Penalty
- Initial $1,000 · Current $1,000
1910.242 B
- Issued
- Aug 5, 1997
- Abate by
- Aug 8, 1997
- Penalty
- Initial $1,000 · Current $1,000
1910.253 B04 I
- Issued
- Aug 5, 1997
- Abate by
- Aug 8, 1997
- Penalty
- Initial $750 · Current $750
1904.2 A
- Issued
- Aug 5, 1997
- Abate by
- Aug 8, 1997
1910.22 A01
- Issued
- Aug 5, 1997
- Abate by
- Sep 8, 1997
1910.95 C01
- Issued
- Aug 5, 1997
- Abate by
- Sep 8, 1997
1910.106 D06 III
- Issued
- Aug 5, 1997
- Abate by
- Sep 8, 1997
More inspections in this industry (NAICS 000000)
More inspections in FL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 110137957.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.