UNION, NJ —
OSHA Inspection: HILLSIDE SPINNING STAMPING CO.
Complaint inspection · Health discipline
At a glance
On , OSHA opened a complaint health inspection of HILLSIDE SPINNING STAMPING CO. in 1060 COMMERCE AVE., UNION, NJ 07083 (NAICS 000000). OSHA activity number 114041171.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- HILLSIDE SPINNING STAMPING CO.
- Site address
- 1060 COMMERCE AVE.
- City
- UNION
- State
- NJ
- ZIP
- 07083
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Complete (A)
- Discipline
- Health
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 3429
- Employees
- 25
- Ownership type
- A
- Industry flags
- Manufacturing health.
Citations
12 citations on file for this inspection.
5(a)(1)
- Issued
- Dec 31, 1991
- Abate by
- Jan 31, 1992
- Penalty
- Initial $875 · Current $450 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: On or about 11/13/91, the employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazard of confined space entry leading to death from asphyxiation from insufficient oxygen or toxic vapors when an employee is required to enter the vapor degreaser tank to perform cleaning and inspection of the tank's interior: a- The employer did not evaluate the hazard of the confined space. The employer did not establish a written permit system to certify that all hazards have been evaluated. Employer did not provide training to employees so that they can work safely in the tanks. Employer did not provide, maintain or ensure the proper use of equipment necessary for safe entry, including testing, monitoring and personal protective equipment. Employer did not ensure that procedures and equipment necessary to rescue employees from the tanks were implemented and provided. Among other methods, one feasible and acceptable abatement method to correc this hazard is to: Implement a confined space entry procedure which includes, but is not limited to, the following items: 1- Instruction and training as to the nature of the hazards involved and necessary precautions to be taken relative to confined space entry. 2- Posting of written confined space entry procedures adjacent to tanks. 3- Issuing a proper entry permit prior to tank entry to ensure that all hazards have been evaluated. 4- Conduct atmospheric testing of tanks to determine potential oxygen deficiency and the presence of air contaminants, prior to employee entry and during the time employee is working in the tank. 5- Where it has been determined that the confined space contains a hazardous concentration of an air contaminant and/or an oxygen deficiency, use of mechanically induced ventilationin the confined space/tank before entry and during occupancy and/or use of respiratory protective equipment which provides adequate protection against the hazards encountered. 6- Provisions and procedures for a standby observer located outside the confined space/tank and readily available standby equipment consisting of a safety line and harness, which employee in the confined space is wearing. 7- Ensure that employees entering the confined space and attendants are properly trained. Training should include, but not be limited to, hazard recognition, communication, protective equipment, rescue.
Recent events (2)
- — I (S) $450.00
- — Z (S) $875.00
1910.37 K02
- Issued
- Dec 31, 1991
- Abate by
- Jan 3, 1992
- Penalty
- Initial $875 · Current $425 Reduced
Recent events (2)
- — I (S) $425.00
- — Z (S) $875.00
1910.94 D08 I
- Issued
- Dec 31, 1991
- Abate by
- Mar 2, 1992
- Penalty
- Initial $525 · Current $250 Reduced
Recent events (2)
- — I (S) $250.00
- — Z (S) $525.00
1910.94 D09 I
- Issued
- Dec 31, 1991
- Abate by
- Jan 31, 1992
- Penalty
- Initial $700 · Current $350 Reduced
Recent events (2)
- — I (S) $350.00
- — Z (S) $700.00
1910.134 B01
- Issued
- Dec 31, 1991
- Abate by
- Jan 31, 1992
Recent events (2)
- — I (S)
- — Z (S)
1910.94 D09 VII
- Issued
- Dec 31, 1991
- Abate by
- Jan 14, 1992
- Penalty
- Initial $700 · Current $350 Reduced
Recent events (2)
- — I (S) $350.00
- — Z (S) $700.00
1910.94 D11 III
- Issued
- Dec 31, 1991
- Abate by
- Mar 2, 1992
- Penalty
- Initial $875 · Current $450 Reduced
Recent events (2)
- — I (S) $450.00
- — Z (S) $875.00
1910.1200 E01 II
- Issued
- Dec 31, 1991
- Abate by
- Jan 31, 1992
Recent events (2)
- — I (S)
- — Z (S)
1910.132 A
- Issued
- Dec 31, 1991
- Abate by
- Jan 14, 1992
- Penalty
- Initial $525 · Current $275 Reduced
Recent events (2)
- — I (S) $275.00
- — Z (S) $525.00
1910.151 C
- Issued
- Dec 31, 1991
- Abate by
- Jan 31, 1992
- Penalty
- Initial $700 · Current $350 Reduced
Recent events (2)
- — I (S) $350.00
- — Z (S) $700.00
1910.217 C01 I
- Issued
- Dec 31, 1991
- Abate by
- Mar 4, 1992
- Penalty
- Initial $700 · Current $350 Reduced
Recent events (2)
- — I (S) $350.00
- — Z (S) $700.00
1910.1200 H02 II
- Issued
- Dec 31, 1991
- Abate by
- Jan 14, 1992
- Penalty
- Initial $700 · Current $350 Reduced
Recent events (2)
- — I (S) $350.00
- — Z (S) $700.00
More inspections at Hillside Spinning Stamping CO.
View Hillside Spinning Stamping CO.'s full OSHA safety record →
More inspections in this industry (NAICS 000000)
More inspections in NJ
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 114041171.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.