SOMERSWORTH, NH —
OSHA Inspection: FEDCO MANUFACTURING CORP., INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of FEDCO MANUFACTURING CORP., INC. in #358, RT. 108, SOMERSWORTH, NH 03878 (NAICS 000000). OSHA activity number 17900937.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- FEDCO MANUFACTURING CORP., INC.
- Site address
- #358, RT. 108
- City
- SOMERSWORTH
- State
- NH
- ZIP
- 03878
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 3443
- Employees
- 13
- Ownership type
- A
- Industry flags
- Manufacturing safety.
Citations
10 citations on file for this inspection.
5(a)(1)
- Issued
- Nov 1, 1991
- Abate by
- Jan 13, 1992
- Penalty
- Initial $875 · Current $570 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The %% employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to: a. Fabrication Shop/Yard - A custom-made spreader beam used to lift steel tanks of up to approximately 8800 pounds (not including rigging) had not been marked to indicate the maximum rated load and had not been proof-tested to 125% of its rated load. ABATEMENT NOTE: One feasible and acceptable abatement method, among others, to correct this hazard is to have the unit marked as to its maximum rated load and proof test it to 125% of the rated load. Rated load test procedures are outlined in ANSI/ASME B30.20-1.4.2 1985 Rated Load Test.
Recent events (2)
- — I (S) $570.00
- — Z (S) $875.00
1910.29 A04 II
- Issued
- Nov 1, 1991
- Abate by
- Nov 8, 1991
- Penalty
- Initial $700 · Current $455 Reduced
Recent events (2)
- — I (S) $455.00
- — Z (S) $700.00
1910.36 B06
- Issued
- Nov 1, 1991
- Abate by
- Nov 15, 1991
- Penalty
- Initial $525 · Current $340 Reduced
Recent events (2)
- — I (S) $340.00
- — Z (S) $525.00
1910.178 A04
- Issued
- Nov 1, 1991
- Abate by
- Nov 8, 1991
- Penalty
- Initial $875 · Current $875
Recent events (2)
- — I (S) $875.00
- — Z (S) $875.00
1910.212 A01
- Issued
- Nov 1, 1991
- Abate by
- Jan 13, 1992
- Penalty
- Initial $570 · Current $570
1910.212 A03 II
- Issued
- Nov 1, 1991
- Abate by
- Nov 4, 1991
- Penalty
- Initial $875 · Current $565 Reduced
Recent events (2)
- — I (S) $565.00
- — Z (S) $875.00
1910.303 B01
- Issued
- Nov 1, 1991
- Abate by
- Nov 8, 1991
- Penalty
- Initial $875 · Current $565 Reduced
Recent events (2)
- — I (S) $565.00
- — Z (S) $875.00
1910.304 E01 IV
- Issued
- Nov 1, 1991
- Abate by
- Nov 4, 1991
- Penalty
- Initial $700 · Current $455 Reduced
Recent events (2)
- — I (S) $455.00
- — Z (S) $700.00
1910.178 A04
- Issued
- Nov 1, 1991
- Abate by
- Dec 2, 1991
Recent events (2)
- — I (O)
- — Z (O)
1910.252 E02 III
- Issued
- Nov 1, 1991
- Abate by
- Nov 15, 1991
More inspections at Fedco Manufacturing Corp., INC.
View Fedco Manufacturing Corp., INC.'s full OSHA safety record →
More inspections in this industry (NAICS 000000)
More inspections in NH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 17900937.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.