Safety Incidents OSHA Severe Injury Reports · 2015–2025
5,189,992Inspections Most recent open 2026-07-18 Last loaded 2026-07-22

OSHA Inspection: ONGARD SYSTEMS, INC.

Complaint inspection · Safety discipline

On , OSHA opened a complaint safety inspection of ONGARD SYSTEMS, INC. in 40 COMMERCE DRIVE, HAUPPAUGE, NY 11788 (NAICS 000000). OSHA activity number 300135183.

What this inspection record means

OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.

Watch Ongard Systems, INC. — free Get an email when a new federal OSHA severe-injury report for Ongard Systems, INC. is published. One employer, no account, unsubscribe in one click.
Site address
40 COMMERCE DRIVE
City
HAUPPAUGE
State
NY
ZIP
11788
Mailing
2116 FINANCIAL CENTER, DES MOINES, IA 50309
Inspection type
Complaint (B)
Scope
Complete (A)
Discipline
Safety
Advance notice
No
Union status
N
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
000000
SIC code (legacy)
3842
Employees
71
Ownership type
A

21 citations on file for this inspection.

5(a)(1)

Serious Gravity 03 1 instance 2 exposed
Issued
Dec 23, 1997
Abate by
Jan 7, 1998
Penalty
Initial $1,250 · Current $1,250
Section 5(a)(1) of the Occupational Safety and Health Act of 1970:  The
employer did not
furnish employment and a place of employment which were free from
recognized hazards that
were causing or likely to cause death or serious physical harm to
employees in that employees
were exposed to: rotating parts of a pipe threading machine.
(a) 9 X 9 Assembly Area - A Ridgid brand power threading
machine / pipe threader, model #400A, was activated by the use
of a toggle switch that cannot automatically shut off. Employee(s)
were exposed to the hazard of inadvertently getting caught in the
rotating parts; On or about 11/06/97.
ABATEMENT NOTES:
Among other methods, one feasible method to reduce this hazard,
is to establish and enforce adequate safe operating procedures.
Procedures such as those found in the operator's manual. Elements
essential to an acceptable safe operating procedure include at a
minimum:
1. Installation and use of a momentary contact device (deadman
foot switch) to control power input to the machine as
recommended by the Ridgid Tool Company foot switch policy,
dated July 1, 1996. This device would automatically stop the
machine and the rotating pipe, if the operator's foot was removed
from the foot switch for any reason.
2. Provide training and education to the machine operators
concerning all the appropriate procedures for the safe operation
and use of this type of machinery, including the use of the foot
switch.
ABATEMENT VERIFICATION IS REQUIRED AS OUTLINED
IN PART 29 CFR 1903.19D

1910.36 D02

Serious Gravity 01 1 instance 3 exposed
Issued
Dec 23, 1997
Abate by
Jan 7, 1998
Penalty
Initial $750 · Current $750

1910.37 Q05

Serious Gravity 01 1 instance 3 exposed
Issued
Dec 23, 1997
Abate by
Jan 7, 1998
Penalty
Initial $750 · Current $750

1910.101 B

Serious Gravity 03 1 instance 2 exposed
Issued
Dec 23, 1997
Abate by
Dec 29, 1997
Penalty
Initial $1,250 · Current $1,250

1910.147 C04 I

Serious Gravity 03 1 instance 12 exposed
Issued
Dec 23, 1997
Abate by
Feb 10, 1998
Penalty
Initial $1,250 · Current $1,250

1910.147 C07 I

Serious Gravity 03 1 instance 12 exposed
Issued
Dec 23, 1997
Abate by
Feb 10, 1998

1910.212 A01

Serious Gravity 03 1 instance 2 exposed
Issued
Dec 23, 1997
Abate by
Dec 29, 1997
Penalty
Initial $1,250 · Current $1,250

1910.212 B

Serious Gravity 01 1 instance 3 exposed
Issued
Dec 23, 1997
Abate by
Dec 26, 1997
Penalty
Initial $637 · Current $637

1910.215 A04

Serious Gravity 01 1 instance 4 exposed
Issued
Dec 23, 1997
Abate by
Dec 26, 1997
Penalty
Initial $637 · Current $637

1910.215 B09

Serious Gravity 01 2 instances 4 exposed
Issued
Dec 23, 1997
Abate by
Dec 26, 1997

1910.219 D01

Serious Gravity 01 1 instance 1 exposed
Issued
Dec 23, 1997
Abate by
Jan 7, 1998
Penalty
Initial $750 · Current $750

1910.219 E03 I

Serious Gravity 01 1 instance 1 exposed
Issued
Dec 23, 1997
Abate by
Jan 7, 1998

1910.242 B

Serious Gravity 01 2 instances 2 exposed
Issued
Dec 23, 1997
Abate by
Dec 26, 1997
Penalty
Initial $637 · Current $637

1910.304 F05 V

Serious Gravity 03 1 instance 4 exposed
Issued
Dec 23, 1997
Abate by
Dec 29, 1997
Penalty
Initial $1,250 · Current $1,250

1910.305 G01 III

Serious Gravity 03 2 instances 2 exposed
Issued
Dec 23, 1997
Abate by
Dec 29, 1997
Penalty
Initial $1,250 · Current $1,250

1904.7

Other-than-serious Gravity 00 4 instances 14 exposed
Issued
Dec 23, 1997
Abate by
Feb 10, 1998

1910.23 A08

Other-than-serious Gravity 01 3 instances 7 exposed
Issued
Dec 23, 1997
Abate by
Jan 7, 1998

1910.132 D01

Other-than-serious Gravity 01 1 instance 14 exposed
Issued
Dec 23, 1997
Abate by
Feb 10, 1998

1910.132 F01

Other-than-serious Gravity 01 1 instance 14 exposed
Issued
Dec 23, 1997
Abate by
Feb 10, 1998

1910.1200 E01

Other-than-serious Gravity 01 1 instance 14 exposed
Issued
Dec 23, 1997
Abate by
Feb 10, 1998

1910.1200 H

Other-than-serious Gravity 01 1 instance 14 exposed
Issued
Dec 23, 1997
Abate by
Feb 10, 1998

View Ongard Systems, INC.'s full OSHA safety record →

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 300135183.

Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.