CORTLAND, NY ·
OSHA Inspection: CENTER STATE BEEF AND VEAL
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of CENTER STATE BEEF AND VEAL in EAST RIVER CROSSINGS ROAD, CORTLAND, NY 13045 (NAICS 000000). OSHA activity number 300631009.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- CENTER STATE BEEF AND VEAL
- Site address
- EAST RIVER CROSSINGS ROAD
- City
- CORTLAND
- State
- NY
- ZIP
- 13045
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 2011
- Employees
- 20
- Ownership type
- A
Citations
21 citations on file for this inspection.
5(a)(1)
- Issued
- Jan 26, 1999
- Abate by
- Feb 28, 1999
- Penalty
- Initial $1,250
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazard of being struck by falling loads and/ or lifting equipment: a)Kill Floor, on or about 9/15/98: All of the hoist controls (One Drum Hoist, and Two Electric Chain Hoists) were not provided with labels showing the direction of hoist travel. ABATEMENT NOTES: Among other methods, one feasible and acceptable method to correct this hazard is to: Install Direction Labels. Follow the labeling requirements set forth in ASME/ANSI B30.16-1987, and ASME/ANSI B30.7-1994. b)Kill Floor, on or about 9/15/98: All of the hoists (One Drum Hoist, and Two Electric Chain Hoists) were not inspected. ABATEMENT NOTES: Among other methods, one feasible and acceptable method to correct this hazard is to: Conduct initial, frequent, and periodic inspections of the hoists and support structures for wear, deterioration or malfunction as per ASME/ANSI B30.16-1987, chapter 16-2, and ASME/ANSI B30.7-1994, chapter 7-2. c)Kill Floor, on or about 9/15/98: All of hoists (One Drum Hoist, and Two Electric Chain Hoists) were not provided with any load ratings. ABATEMENT NOTES: Among other methods, one feasible and acceptable method to correct this hazard is to: Provide load ratings for the hoists, hooks, chains, and support structures as per ASME/ANSI B30.16-1987, chapter 16-1, and ASME/ANSI B30.7-1994, chapter 7- 1.1. d)Kill Floor, on or about 9/15/98: All of the hoists (One Drum Hoist, and Two Electric Chain Hoists) were not provided with limit switches. ABATEMENT NOTES: Among other methods, one feasible and acceptable method to correct this hazard is to: Provided operational limit switches as per ASME/ANSI B30.16-1987, and ASME/ANSI B30.7-1994, chapter 7-2.2. e)Kill Floor, on or about 9/15/98: The Monorail transport system used to transport cattle was not provided with inspections, records of inspections, and maximum tonnage. ABATEMENT NOTES: Among other methods, one feasible and acceptable method to correct this hazard is to: Conduct initial, frequent, and periodic inspections of the hoists and support structures for wear, deterioration or malfunction as per ANSI B30.11-1973, chapter 11-2. Abatement certification is required for these items.
Recent events (2)
- · I (S)
- · Z (S) $1250.00
5(a)(1)
- Issued
- Jan 26, 1999
- Abate by
- Feb 28, 1999
- Penalty
- Initial $1,250
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazard of being shot by a .22 caliber rifle: a)Kill Floor, on or about 9/15/98: Safe gun handling rules were not being followed while a .22 caliber rifle was used to slaughter bovine. ABATEMENT NOTES: Among other methods, one feasible and acceptable method to correct this hazard is to: 1) Always keep the gun pointed in a safe direction. 2) Know the target and what is beyond it. 3) Ensure that the gun is safe to operate (no missing or broken trigger guards). 4) Wear hearing and eye protection as appropriate. 5) Store guns so that they are not accessible to unauthorized persons. 6) Follow the National Rifle Associations fundamental rules of gun safety. 7) Follow the gun safety rules set forth by the New York State DEC hunter education course. Abatement certification is required for this item.
Recent events (2)
- · I (S)
- · Z (S) $1250.00
1910.23 C01
- Issued
- Jan 26, 1999
- Abate by
- Feb 28, 1999
- Penalty
- Initial $2,500
Recent events (2)
- · I (S)
- · Z (S) $2500.00
1910.25 D02 XII
- Issued
- Jan 26, 1999
- Abate by
- Feb 13, 1999
- Penalty
- Initial $1,000
Recent events (2)
- · I (S)
- · Z (S) $1000.00
1910.36 B04
- Issued
- Jan 26, 1999
- Abate by
- Jan 29, 1999
- Penalty
- Initial $2,500
Recent events (2)
- · I (S)
- · Z (S) $2500.00
1910.132 D01
- Issued
- Jan 26, 1999
- Abate by
- Feb 28, 1999
- Penalty
- Initial $1,250
Recent events (2)
- · I (S)
- · Z (S) $1250.00
1910.132 F01
- Issued
- Jan 26, 1999
- Abate by
- Feb 28, 1999
Recent events (2)
- · I (S)
- · Z (S)
1910.132 F04
- Issued
- Jan 26, 1999
- Abate by
- Feb 28, 1999
Recent events (2)
- · I (S)
- · Z (S)
1910.133 A01
- Issued
- Jan 26, 1999
- Abate by
- Feb 28, 1999
- Penalty
- Initial $1,250
Recent events (2)
- · I (S)
- · Z (S) $1250.00
1910.151 C
- Issued
- Jan 26, 1999
- Abate by
- Feb 28, 1999
- Penalty
- Initial $1,250
Recent events (2)
- · I (S)
- · Z (S) $1250.00
1910.219 D01
- Issued
- Jan 26, 1999
- Abate by
- Feb 28, 1999
- Penalty
- Initial $1,000
Recent events (2)
- · I (S)
- · Z (S) $1000.00
1910.219 E01 I
- Issued
- Jan 26, 1999
- Abate by
- Feb 28, 1999
Recent events (2)
- · I (S)
- · Z (S)
1910.303 C
- Issued
- Jan 26, 1999
- Abate by
- Feb 13, 1999
- Penalty
- Initial $1,000
Recent events (2)
- · I (S)
- · Z (S) $1000.00
1910.303 G02 I
- Issued
- Jan 26, 1999
- Abate by
- Feb 13, 1999
- Penalty
- Initial $1,000
Recent events (2)
- · I (S)
- · Z (S) $1000.00
1910.304 A02
- Issued
- Jan 26, 1999
- Abate by
- Feb 13, 1999
- Penalty
- Initial $1,000
Recent events (2)
- · I (S)
- · Z (S) $1000.00
1910.304 F05 V
- Issued
- Jan 26, 1999
- Abate by
- Feb 13, 1999
- Penalty
- Initial $1,000
Recent events (2)
- · I (S)
- · Z (S) $1000.00
1910.305 J02 II
- Issued
- Jan 26, 1999
- Abate by
- Feb 13, 1999
- Penalty
- Initial $1,000
Recent events (2)
- · I (S)
- · Z (S) $1000.00
1910.305 G02 III
- Issued
- Jan 26, 1999
- Abate by
- Feb 13, 1999
Recent events (2)
- · I (O)
- · Z (O)
1910.1200 E01
- Issued
- Jan 26, 1999
- Abate by
- Feb 28, 1999
Recent events (2)
- · I (O)
- · Z (O)
1910.1200 G08
- Issued
- Jan 26, 1999
- Abate by
- Feb 28, 1999
Recent events (2)
- · I (O)
- · Z (O)
1910.1200 H01
- Issued
- Jan 26, 1999
- Abate by
- Feb 28, 1999
Recent events (2)
- · I (O)
- · Z (O)
More inspections at Center State Beef and Veal
View Center State Beef and Veal's full OSHA safety record →
More inspections in this industry (NAICS 000000)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 300631009.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.