BATTLEBORO, NC —
OSHA Inspection: GEMINI TEXTILE SCREENPRINT, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of GEMINI TEXTILE SCREENPRINT, INC. in 7101 HWY 301 N., BATTLEBORO, NC 27809 (NAICS 000000). OSHA activity number 302117650.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- GEMINI TEXTILE SCREENPRINT, INC.
- Site address
- 7101 HWY 301 N.
- City
- BATTLEBORO
- State
- NC
- ZIP
- 27809
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 2261
- Employees
- 30
- Ownership type
- A
- Industry flags
- Manufacturing safety.
Citations
9 citations on file for this inspection.
95012901
- Issued
- Apr 8, 1998
- Abate by
- Apr 13, 1998
- Penalty
- Initial $700 · Current $700
General-duty citation text
North Carolina General Statue 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish to each of his employees conditions of employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees, in that employees were exposed to being crushed by the trash compactor ram because the emergency stop controls were not readily accessible to the operator:: a)trash compactor -- when the employee was dumping trash from 50 gallon plastic trash cans, the Emergency Stop controls were 7' from the operator.(Ref. ANSI Z245.2 1992, Sec 7.5.3) one feasible and acceptable method, among others, to correct the hazard is to relocate the control panel to a point 3' from the employee while the employee is dumping trash.g
1910.147 C01
- Issued
- Apr 8, 1998
- Abate by
- Apr 26, 1998
- Penalty
- Initial $250 · Current $250
1910.304 F04
- Issued
- Apr 8, 1998
- Abate by
- Apr 26, 1998
- Penalty
- Initial $250 · Current $250
1910.305 G01 III
- Issued
- Apr 8, 1998
- Abate by
- Apr 26, 1998
- Penalty
- Initial $700 · Current $700
1910.334 A02 I
- Issued
- Apr 8, 1998
- Abate by
- Apr 26, 1998
- Penalty
- Initial $500 · Current $500
7F0102
- Issued
- Apr 8, 1998
- Abate by
- Apr 26, 1998
1910.22 D01
- Issued
- Apr 8, 1998
- Abate by
- Apr 26, 1998
1910.38 A01
- Issued
- Apr 8, 1998
- Abate by
- Apr 26, 1998
1910.157 G02
- Issued
- Apr 8, 1998
- Abate by
- Apr 26, 1998
More inspections in this industry (NAICS 000000)
More inspections in NC
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 302117650.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.