JACKSON, MS —
OSHA Inspection: G & O MANUFACTURING COMPANY
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of G & O MANUFACTURING COMPANY in 1420 RIDGEWAY STREET, JACKSON, MS 39213 (NAICS 000000). OSHA activity number 302399241.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- G & O MANUFACTURING COMPANY
- Site address
- 1420 RIDGEWAY STREET
- City
- JACKSON
- State
- MS
- ZIP
- 39213
- Mailing
- 1420 RIDGEWAY STREET, JACKSON, MS 39213
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Y
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 3714
- Employees
- 265
- Ownership type
- A
- Industry flags
- Manufacturing safety.
Citations
12 citations on file for this inspection.
5(a)(1)
- Issued
- Feb 2, 2001
- Abate by
- Mar 22, 2001
- Penalty
- Initial $975 · Current $975
General-duty citation text
Section 5(a)(1) of Public Law 91-596, the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees, in that employees were exposed to the hazard of being struck by falling loads: On January 12, and 16, 2001, during the assembly process in Silver Solder, Off Highway, and departments throughout the plant, purchased and shop made below-the- hook lifting devices were used on cranes and hoists and the lifting devices had no nameplate or permanent marking identifying the manufacturer's name and address, serial number, lifter weight, and rated load. (Reference ANSI/ASME B30.20b-1996, Below- The-Hook Lifting Devices, Chapter 20-1, Section 20-1.2), Among other methods, one feasible and acceptable abatement method is to affix a nameplate or other permanent marking to the devices in accordance with the requirements of ANSI/ASME B30.20b-1996.
1910.184 E01
- Issued
- Feb 2, 2001
- Abate by
- Mar 22, 2001
- Penalty
- Initial $975 · Current $975
1910.184 C02
- Issued
- Feb 2, 2001
- Abate by
- Mar 22, 2001
1910.184 D
- Issued
- Feb 2, 2001
- Abate by
- Mar 22, 2001
1910.184 E02 II
- Issued
- Feb 2, 2001
- Abate by
- Mar 22, 2001
1910.217 C01 I
- Issued
- Feb 2, 2001
- Abate by
- Mar 1, 2001
- Penalty
- Initial $1,625 · Current $1,625
1910.242 B
- Issued
- Feb 2, 2001
- Abate by
- Feb 14, 2001
- Penalty
- Initial $975 · Current $975
1910.253 B04 III
- Issued
- Feb 2, 2001
- Abate by
- Feb 14, 2001
- Penalty
- Initial $975 · Current $975
1910.22 A03
- Issued
- Feb 2, 2001
- Abate by
- Feb 14, 2001
1910.22 D01
- Issued
- Feb 2, 2001
- Abate by
- Mar 1, 2001
1910.37 Q01
- Issued
- Feb 2, 2001
- Abate by
- Feb 14, 2001
1910.147 C04 IIB
- Issued
- Feb 2, 2001
- Abate by
- Mar 22, 2001
More inspections at G & O Manufacturing Company
View G & O Manufacturing Company's full OSHA safety record →
More inspections in this industry (NAICS 000000)
More inspections in MS
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 302399241.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.