ROCKFORD, IL —
OSHA Inspection: COLMAN METAL FINISHING
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of COLMAN METAL FINISHING in 1300 ROCK ST., ROCKFORD, IL 61101 (NAICS 000000). OSHA activity number 302608815.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- COLMAN METAL FINISHING
- Site address
- 1300 ROCK ST.
- City
- ROCKFORD
- State
- IL
- ZIP
- 61101
- Mailing
- P.O. BOX 2940, ROCKFORD, IL 61132
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 3471
- Employees
- 47
- Ownership type
- A
Citations
6 citations on file for this inspection.
5(a)(1)
- Issued
- Aug 30, 2000
- Abate by
- Oct 2, 2000
- Penalty
- Initial $1,700 · Current $1,000 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were likely to cause death or serious physical harm to employees in that employees were exposed to being struck by a displaced load: Coleman Metal Finishing used a custom made lifting device to lift basket loaded with metal weighing approximately 200 - 300 pounds. Feasible and acceptable abatement methods include, but are not necessarily limited to: Comply with ANSI B30.20 - Below the Hook Lifting Devices and: 1. Provide the rated load on any custom made lifting device: 2.Design the lifting device to withstand the forces imposed by its rated load with a minimum design factor of 3. 3. Provide initial, frequent and periodic inspections of the lifting devices. 4. Ensure that lifting device must be securely attached to the load. CERTIFICATION REQUIRED FOR THIS ITEM
Recent events (2)
- — I (S) $1000.00
- — Z (S) $1700.00
1910.136 A
- Issued
- Aug 30, 2000
- Abate by
- Oct 2, 2000
Recent events (2)
- — I (S)
- — Z (S)
1910.22 B01
- Issued
- Aug 30, 2000
- Abate by
- Oct 2, 2000
- Penalty
- Initial $1,700 · Current $1,000 Reduced
Recent events (2)
- — I (S) $1000.00
- — Z (S) $1700.00
1910.23 C02
- Issued
- Aug 30, 2000
- Abate by
- Oct 2, 2000
- Penalty
- Initial $1,700 · Current $1,000 Reduced
Recent events (2)
- — I (S) $1000.00
- — Z (S) $1700.00
1910.23 C01
- Issued
- Aug 30, 2000
- Abate by
- Oct 2, 2000
Recent events (2)
- — I (S)
- — Z (S)
1910.179 J03
- Issued
- Aug 30, 2000
- Abate by
- Oct 2, 2000
Recent events (2)
- — I (O)
- — Z (O)
More inspections at Colman Metal Finishing
View Colman Metal Finishing's full OSHA safety record →
More inspections in this industry (NAICS 000000)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 302608815.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.