GOLDSBORO, NC —
OSHA Inspection: THE STANDARD PRODUCTS COMPANY
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of THE STANDARD PRODUCTS COMPANY in 308 FEDELON TRAIL, GOLDSBORO, NC 27530 (NAICS 000000). OSHA activity number 302866587.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- THE STANDARD PRODUCTS COMPANY
- Site address
- 308 FEDELON TRAIL
- City
- GOLDSBORO
- State
- NC
- ZIP
- 27530
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 3714
- Employees
- 784
- Ownership type
- A
- Industry flags
- Manufacturing safety.
Citations
14 citations on file for this inspection.
95012901
- Issued
- Jun 29, 1999
- Abate by
- Jul 17, 1999
- Penalty
- Initial $1,250 · Current $1,250
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish each of his employees conditions of employment and a place of employment free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to a crushing hazard: A latch was not provided to bridge the throat opening of the hook for he purpose of retaining slings, chains, etc., under slack conditions (ref. ANSI B30.16-1981 Sec 16-1.2.9): Frequent visual examinations of all functional operating mechanisms for misadjustment interfering with proper operation, deformed, chemically damaged, or cracked hooks, hook latches, and hoist load chain by the operator or other designated personnel, with records not required, were not performed on a monthly basis for hoist used under normal service (ref. ANSI B30.16-1981 Sec 16-2.1.2): a)Primary area, line 1 and line 3 final side - two, 2-ton, CM Loadstar, electric chain hoists, used for lifting 988 lb. catapullers and 1,308 lb. rafts. One feasible and acceptable method of abatement, among others, to correct this hazard is to have a certified crane company to install safety latches on the appropriate hooks; have designated and qualified person to perform frequent inspections of the hoists to ensure compliance with applicable provisions of this standard.
1910.178 K01
- Issued
- Jun 29, 1999
- Abate by
- Jul 2, 1999
- Penalty
- Initial $1,750 · Current $1,750
1910.212 A01
- Issued
- Jun 29, 1999
- Abate by
- Aug 1, 1999
- Penalty
- Initial $1,250 · Current $1,250
1910.212 B
- Issued
- Jun 29, 1999
- Abate by
- Aug 1, 1999
1910.304 F04
- Issued
- Jun 29, 1999
- Abate by
- Jul 2, 1999
- Penalty
- Initial $1,750 · Current $1,750
1910.305 G02 III
- Issued
- Jun 29, 1999
- Abate by
- Jul 2, 1999
- Penalty
- Initial $875 · Current $875
1910.132 D02
- Issued
- Jun 29, 1999
- Abate by
- Jul 17, 1999
1910.132 C
- Issued
- Jun 29, 1999
- Abate by
- Jul 17, 1999
1910.217 E01 II
- Issued
- Jun 29, 1999
- Abate by
- Jul 17, 1999
1910.303 B01
- Issued
- Jun 29, 1999
- Abate by
- Jul 17, 1999
1910.303 F
- Issued
- Jun 29, 1999
- Abate by
- Jul 17, 1999
1910.303 G01 II
- Issued
- Jun 29, 1999
- Abate by
- Jul 17, 1999
1910.305 G01 III
- Issued
- Jun 29, 1999
- Abate by
- Jul 17, 1999
1910.1200 H
- Issued
- Jun 29, 1999
- Abate by
- Jul 17, 1999
More inspections at The Standard Products Company
View The Standard Products Company's full OSHA safety record →
More inspections in this industry (NAICS 000000)
More inspections in NC
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 302866587.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.