FRIANT, CA —
OSHA Inspection: TMR ENTERPRISES
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of TMR ENTERPRISES in 8184 TABLE MOUNTAIN RD, FRIANT, CA 93626 (NAICS 000000). OSHA activity number 303337679.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- TMR ENTERPRISES
- Site address
- 8184 TABLE MOUNTAIN RD
- City
- FRIANT
- State
- CA
- ZIP
- 93626
- Mailing
- PO BOX 680, FRIANT, CA 93626
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 1542
- Employees
- 100
- Ownership type
- A
- Industry flags
- Construction safety.
Citations
6 citations on file for this inspection.
5(a)(1)
- Issued
- Nov 2, 2000
- Abate by
- Nov 8, 2000
- Penalty
- Initial $875 · Current $875
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to: a)Table Mountain Casino expansion, first floor - Two Genie GS-3268 scissor lifts were being used to raise 22 ft and 25 ft re-shoring towers into the vertical position. This was accomplished by resting or tieing one end of the re-shoring tower to the guardrail of the scissor lift and having the operator raise the platform. Other employees on the ground would push the foot of the tower into place while it was being raised. Use of this personnel platform in this manner is not approved by the manufacturer and recognized as a tipping hazard. On or about 10/18/00. ABATEMENT NOTE: Among other methods, one feasible method to reduce this hazard is to: 1.Follow national consensus standard ANSI/SIA A92.6 and manufacturer's operation manual, and 2.Use all self-propelled elevating work platforms (scissor lifts) only for the purpose for which they are designed. Prohibit use of scissor lifts as material lifting devices. ABATEMENT DOCUMENTATION AND VERIFICATION IS REQUIRED.ION
1926.501 B01
- Issued
- Nov 2, 2000
- Abate by
- Nov 8, 2000
- Penalty
- Initial $875 · Current $875
1926.1053 B04
- Issued
- Nov 2, 2000
- Abate by
- Nov 8, 2000
1926.502 D17
- Issued
- Nov 2, 2000
- Abate by
- Nov 8, 2000
- Penalty
- Initial $875 · Current $875
1926.502 D23
- Issued
- Nov 2, 2000
- Abate by
- Nov 8, 2000
- Penalty
- Initial $875 · Current $875
1926.1053 B04
- Issued
- Nov 2, 2000
- Abate by
- Nov 8, 2000
More inspections at TMR Enterprises
View TMR Enterprises's full OSHA safety record →
More inspections in this industry (NAICS 000000)
More inspections in CA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 303337679.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.