MAIDEN, NC ·
OSHA Inspection: SOLUS INDUSTRIAL INNOVATIONS, LLC
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of SOLUS INDUSTRIAL INNOVATIONS, LLC in 10 N MAIN AVENUE, MAIDEN, NC 28650 (NAICS 000000). OSHA activity number 304543051.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- SOLUS INDUSTRIAL INNOVATIONS, LLC
- Site address
- 10 N MAIN AVENUE
- City
- MAIDEN
- State
- NC
- ZIP
- 28650
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 2499
- Employees
- 14
- Ownership type
- A
- Industry flags
- Manufacturing safety.
Citations
22 citations on file for this inspection.
95012901
- Issued
- Jun 28, 2001
- Abate by
- Aug 15, 2001
- Penalty
- Initial $1,400 · Current $1,400
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish to each of his employees conditions of employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to: a)being crushed by or caught between the forklift and the ground in the event of an overturn hazard. An employee, operating the Toyota Forklift next to the warehouse, was not wearing the seat belt while operating the forklift. Among other methods, one feasible and acceptable abatement method to correct this hazard is to train employees and enforce the wearing of seat belts while operating forklifts with a Roll Over Protection system (ROPS) or a Fall On Protection System (FOPS). b)being crushed by or caught between the forklift and the ground in the event of an overturn hazard. The Toyota Forklift, located in the Impregnating Room, was not equipped with a seat belt. Among other methods, one feasible and acceptable abatement method to correct this hazard is to retro-fit any forklifts, purchased without a seat belt, with seat belts from the manufacturer, then to train the employees and enforce the wearing of seat belts while operating forklifts with a Roll Over Protection system (ROPS) or a Fall On Protection System (FOPS). [Reference: ASME/ANSI B56.1a-1980 Addenda to ASME/ANSI B56.1-1988, and ASME B56.1-1993 - Safety Standard for Low Lift and High Lift Trucks]d
1910.178 L01 I
- Issued
- Jun 28, 2001
- Abate by
- Aug 15, 2001
1910.212 A01
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
- Penalty
- Initial $1,000 · Current $1,000
1910.212 A03 II
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
1910.215 A04
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
- Penalty
- Initial $1,000 · Current $1,000
1910.215 B05
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
1910.215 B09
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
1910.219 D01
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
- Penalty
- Initial $1,000 · Current $1,000
1910.219 E01 I
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
1910.219 E03 I
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
7F0102
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
1910.23 D01 II
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
1910.157 C01
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
1910.157 E01
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
1910.159 C02
- Issued
- Jun 28, 2001
- Abate by
- Aug 15, 2001
1910.212 B
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
1910.303 G01 I
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
1910.304 F04
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
1910.305 B01
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
1910.305 B02
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
1910.334 A02 I
- Issued
- Jun 28, 2001
- Abate by
- Jul 9, 2001
1904.2 B02
- Issued
- Jun 28, 2001
- Abate by
- Jul 3, 2001
More inspections at Solus Industrial Innovations, LLC
View Solus Industrial Innovations, LLC's full OSHA safety record →
More inspections in this industry (NAICS 000000)
More inspections in NC
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 304543051.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.