MUNDELEIN, IL ·
OSHA Inspection: BARBER-COLMAN COMPANY DBA FUEL MANAGEMENT SYSTEMS
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of BARBER-COLMAN COMPANY DBA FUEL MANAGEMENT SYSTEMS in 408 WASHINGTON BOULEVARD, MUNDELEIN, IL 60060 (NAICS 000000). OSHA activity number 304585334.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- BARBER-COLMAN COMPANY DBA FUEL MANAGEMENT SYSTEMS
- Site address
- 408 WASHINGTON BOULEVARD
- City
- MUNDELEIN
- State
- IL
- ZIP
- 60060
- Mailing
- 408 WASHINGTON BOULEVARD, MUNDELEIN, IL 60060
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (N)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 8711
- Employees
- 8
- Ownership type
- Private (A)
Citations
4 citations on file for this inspection.
5(a)(1)
- Issued
- Jul 16, 2001
- Abate by
- Aug 30, 2001
- Penalty
- Initial $825 · Current $578 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to: (a) Horizontal Band Saw Area, South Wall - the Wholesale horizontal band saw was not equipped with a magnetic restarter or similar device, as prescribed by the American National Standard for Metal Cutting Saws, ANSI B11.10 - 1990, Section 5.2.3.4, that in the event of an interruption in the electrical supply, would prevent the saw from restarting automatically when power is restored. (b) Horizontal Band Saw Area, South Wall - the Wholesale horizontal band saw was equipped with an unprotected, toggle type motor starter switch instead of a starter located, designed, constructed, interlocked or guarded to protect against unintended operation, as prescribed by the American National ANSI Standard for Metal Cutting Saws, ANSI B11.10 - 1990, Section 5.2.3.1. Abatement certification only is required for this item in accordance with the requirements of 29 CFR 1903.19(c).
Recent events (2)
- · I (S) $577.50
- · Z (S) $825.00
1910.212 A01
- Issued
- Jul 16, 2001
- Abate by
- Aug 30, 2001
- Penalty
- Initial $825 · Current $578 Reduced
Recent events (2)
- · I (S) $577.50
- · Z (S) $825.00
1910.219 D01
- Issued
- Jul 16, 2001
- Abate by
- Aug 30, 2001
- Penalty
- Initial $825 · Current $578 Reduced
Recent events (2)
- · I (S) $577.50
- · Z (S) $825.00
1910.219 E03 I
- Issued
- Jul 16, 2001
- Abate by
- Aug 30, 2001
More inspections at Barber-Colman Company DBA Fuel Management Systems
View Barber-Colman Company DBA Fuel Management Systems's full OSHA safety record →
More inspections in this industry (NAICS 000000)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 304585334.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.