FULTON, NY —
OSHA Inspection: BREWER AND BREWER
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of BREWER AND BREWER in 214 WEST BROADWAY, FULTON, NY 13069 (NAICS 000000). OSHA activity number 304590631.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- BREWER AND BREWER
- Site address
- 214 WEST BROADWAY
- City
- FULTON
- State
- NY
- ZIP
- 13069
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 5541
- Employees
- 4
- Ownership type
- A
Citations
4 citations on file for this inspection.
5(a)(1)
- Issued
- Sep 12, 2002
- Abate by
- Sep 25, 2002
- Penalty
- Initial $375 · Current $375
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to THE HAZARD OF BEING CRUSHED-BY THE LOAD : a)Vehicle Repair Area, West Bay, on or about 4/24/02: Periodic inspections (every 3 months) for Benwil model FP-7X, automotive lift, sn.41610, capacity 7000lbs., were not being done and/or recorded per lift manufacturer's recommendations and ANSI/ALI ALOIM-2000. Employee was operating a Benwil model FP-7X, automotive lift, sn. 41610 when wire rope lifting cable broke. Wire rope was not being serviced or maintained per manufacturer's manual. ABATEMENT NOTE: One feasible means of abatement is to ensure that periodic inspections (every 3 months) are performed and recorded per manufacturers manual pages 1 and 5, also ANSI/ALI ALOIM-2000, Chapter 5, Section 5.1, 5.4, and 5.6.1.and ensure that wire rope is serviced and maintained per manufacturer's manual pages 1 and 5. b)Vehicle Repair Area, Center Bay, on or about 4/24/02: Periodic inspections for Autolift model 9000, 2 post, automotive lift, capacity 9000lbs., were not being done and/or recorded per lift manufacturer's recommendation and/or ANSI/ALI ALOIM-2000. ABATEMENT NOTE: One feasible means of abatement is to ensure that periodic inspections are performed and recorded per manufacturer's manual and also ANSI/ALI ALOIM-2000, Chapter 5, Section 5.1, 5.4, and 5.6.1. Abatement certification must be submitted for this item. c)Vehicle Repair Area, East Bay, on or about 4/24/02: Periodic inspections for Challenger II, 2 post, automotive lift, sn.212417, were not being done and/or recorded per lift manufacturer's recommendation and/or ANSI/ALI ALOIM- 2000. ABATEMENT NOTE: One feasible means of abatement is to ensure that periodic inspections are performed and recorded per manufacturer's manual and also ANSI/ALI ALOIM-2000, Chapter 5.1, 5.4, and 5.6.1. Abatement certification must be submitted for this item.
1910.1200 E01
- Issued
- Sep 12, 2002
- Abate by
- Sep 25, 2002
1910.1200 G08
- Issued
- Sep 12, 2002
- Abate by
- Sep 25, 2002
1910.1200 H01
- Issued
- Sep 12, 2002
- Abate by
- Sep 25, 2002
More inspections in this industry (NAICS 000000)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 304590631.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.