BRYAN, OH —
OSHA Inspection: A-STAMP INDUSTRIES
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of A-STAMP INDUSTRIES in 633 COMMERCE DRIVE, BRYAN, OH 43506 (NAICS 000000). OSHA activity number 305114258.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- A-STAMP INDUSTRIES
- Site address
- 633 COMMERCE DRIVE
- City
- BRYAN
- State
- OH
- ZIP
- 43506
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 000000
- SIC code (legacy)
- 3465
- Employees
- 26
- Ownership type
- A
Citations
5 citations on file for this inspection.
5(a)(1)
- Issued
- Aug 8, 2002
- Abate by
- Aug 27, 2002
- Penalty
- Initial $1,250 · Current $1,000 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that: a) A-Stamp Industries, Bryan, Ohio: As determined on or about June 10, 2002, during production operations on the Minster 500 ton part revolution mechanical power press, employees were using the "inch mode" to stamp parts during "station-to-station" hands-in-die press operations. During the use of the "inch mode" as described, the brake monitor did not monitor the performance of the brake, additional wear was placed on mechanical parts such as the brake and clutch and there was no single stroke/anti-repeat mechanism while operating in the "inch mode", which allowed the press to cycle continuously as long as the two control buttons were depressed. Among other methods, feasible and acceptable methods to correct this hazard would be to run production operations in another mode and cease the use of the "inch" mode during production operations, following the recommendations of the press manufacturer, which states: 1. Minster Press Company Manual, page 30: NEVER RUN PRODUCTION ON A PRESS WITH STROKING SELECTOR IN THE INCH MODE. INCHING IS A FUNCTION TO BE USED BY THE DIE SETTER FOR SET-UP OF DIES AND TOOLING, OR, FOR MECHANIC'S USE WHEN CONTROLLED INTERMITTENT MOTION OF THE SLIDE IS REQUIRED. Or the employer could follow the precepts of ANSI B11.1-2001, Safety Requirements for Mechanical Power Presses, which states: 2. ANSI B11.1, 2001, section 6.12.3.3.2, Inch: The INCH operating mode shall not be used as a production mode. Additional abatement information is required for this item.
Recent events (2)
- — J (S) $1000.00
- — Z (S) $1250.00
1910.217 C03 IIIF
- Issued
- Aug 8, 2002
- Abate by
- Aug 27, 2002
- Penalty
- Initial $2,500 · Current $1,000 Reduced
Recent events (2)
- — J (S) $1000.00
- — Z (S) $2500.00
1910.217 E01 I
- Issued
- Aug 8, 2002
- Abate by
- Aug 27, 2002
- Penalty
- Initial $1,250 · Current $1,000 Reduced
Recent events (2)
- — J (S) $1000.00
- — Z (S) $1250.00
1910.217 E03
- Issued
- Aug 8, 2002
- Abate by
- Sep 25, 2002
- Penalty
- Initial $2,500 · Current $1,000 Reduced
Recent events (2)
- — J (S) $1000.00
- — Z (S) $2500.00
1910.217 F02
- Issued
- Aug 8, 2002
- Abate by
- Aug 27, 2002
- Penalty
- Initial $2,500 · Current $1,000 Reduced
Recent events (2)
- — J (S) $1000.00
- — Z (S) $2500.00
More inspections at A-Stamp Industries
View A-Stamp Industries's full OSHA safety record →
More inspections in this industry (NAICS 000000)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 305114258.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.