STOW, OH ·
OSHA Inspection: STEEL PRODUCTS CORPORATION OF AKRON
Accident-driven inspection · Safety discipline
At a glance
On , OSHA opened an accident-driven safety inspection of STEEL PRODUCTS CORPORATION OF AKRON in 1699 COMMERCE DRIVE, STOW, OH 44224 (NAICS 332710). OSHA activity number 305329443.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- STEEL PRODUCTS CORPORATION OF AKRON
- Site address
- 1699 COMMERCE DRIVE
- City
- STOW
- State
- OH
- ZIP
- 44224
What kind of inspection was it?
- Inspection type
- Accident-driven (A)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (N)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332710
- SIC code (legacy)
- 3599
- Employees
- 20
- Ownership type
- Private (A)
Citations
17 citations on file for this inspection.
5(a)(1)
- Issued
- Nov 7, 2003
- Abate by
- Jan 20, 2005
- Penalty
- Initial $1,500 · Current $1,000 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: the employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees, in that employees were exposed to struck-by hazards by ejected parts: On July 15, 2003, employees were exposed to the hazards of being struck by a 1,100 pound, unbalanced part from the Giddings & Lewis CNC Vertical Boring Mill, S/N 513-59-79, company No. V10, during post milling cleaning operations. While in manual mode, the table, with the part mounted, was spun at a high rate of speed, in an effort to remove chips, cutting fluids, coolants, and water by centrifugal force, causing the part to be ejected from the chuck clamps. Feasible and acceptable methods to eliminate this hazard would be, but not limited to: A) secure the selection of the table speed manual mode of operation by either key-switch, access code or an equally secure means capable of being supervised; B) establish a written safe cleaning procedure, properly train the operator in the use of the procedure, the hazards involved and ensure the operation of the machine is properly supervised, as established in ANSI B11.23-2002, Safety Requirements for Machining Centers and Automatic, Numerically Controlled Milling, Drilling and Boring Machines.
Recent events (2)
- · F (S) $1000.00
- · Z (S) $1500.00
1910.147 C01
- Issued
- Nov 7, 2003
- Abate by
- Jan 20, 2005
- Penalty
- Initial $750 · Current $400 Reduced
Recent events (2)
- · F (S) $400.00
- · Z (S) $750.00
1910.157 G02
- Issued
- Nov 7, 2003
- Abate by
- Jan 20, 2005
- Penalty
- Initial $750
Recent events (2)
- · F (O)
- · Z (S) $750.00
1910.178 Q07
- Issued
- Nov 7, 2003
- Abate by
- Jan 20, 2005
Recent events (2)
- · F (O)
- · Z (O)
1910.179 J02
- Issued
- Nov 7, 2003
- Abate by
- Jan 20, 2005
- Penalty
- Initial $450 · Current $450
Recent events (2)
- · F (S) $450.00
- · Z (S) $450.00
1910.179 J03
- Issued
- Nov 7, 2003
- Abate by
- Jan 20, 2005
Recent events (2)
- · F (S)
- · Z (S)
1910.179 N04 I
- Issued
- Nov 7, 2003
- Abate by
- Jan 20, 2005
Recent events (2)
- · F (S)
- · Z (S)
1910.179 N04 I
- Issued
- Nov 7, 2003
- Abate by
- Nov 25, 2003
- Penalty
- Initial $450 · Current $450
Recent events (2)
- · F (S) $450.00
- · Z (S) $450.00
1910.212 A01
- Issued
- Nov 7, 2003
- Abate by
- Feb 20, 2005
- Penalty
- Initial $1,500 · Current $750 Reduced
Recent events (2)
- · F (S) $750.00
- · Z (S) $1500.00
1910.242 B
- Issued
- Nov 7, 2003
- Abate by
- Nov 13, 2003
- Penalty
- Initial $600 · Current $400 Reduced
Recent events (2)
- · F (S) $400.00
- · Z (S) $600.00
1910.1200 E01
- Issued
- Nov 7, 2003
- Abate by
- Nov 13, 2003
- Penalty
- Initial $450 · Current $400 Reduced
Recent events (2)
- · F (S) $400.00
- · Z (S) $450.00
1910.1200 F05 I
- Issued
- Nov 7, 2003
- Abate by
- Jan 20, 2005
Recent events (2)
- · F (S)
- · Z (S)
1910.1200 F05 II
- Issued
- Nov 7, 2003
- Abate by
- Jan 20, 2005
Recent events (2)
- · F (S)
- · Z (S)
1910.1200 H01
- Issued
- Nov 7, 2003
- Abate by
- Jan 20, 2005
Recent events (2)
- · F (S)
- · Z (S)
1904.4 A
- Issued
- Nov 7, 2003
- Abate by
- Nov 13, 2003
- Penalty
- Initial $600 · Current $300 Reduced
Recent events (2)
- · F (O) $300.00
- · Z (O) $600.00
1910.157 E02
- Issued
- Nov 7, 2003
- Abate by
- Jan 20, 2005
Recent events (2)
- · F (O)
- · Z (O)
1910.178 L06
- Issued
- Nov 7, 2003
- Abate by
- Dec 10, 2003
Recent events (2)
- · F (O)
- · Z (O)
More inspections at Steel Products Corporation of Akron
View Steel Products Corporation of Akron's full OSHA safety record →
More inspections in this industry (NAICS 332710)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 305329443.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.