AUBURN, NY —
OSHA Inspection: BO-MER PLASTICS
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of BO-MER PLASTICS in 13 PULASKI STREET, AUBURN, NY 13021 (NAICS 326121). OSHA activity number 306311937.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- BO-MER PLASTICS
- Site address
- 13 PULASKI STREET
- City
- AUBURN
- State
- NY
- ZIP
- 13021
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Data loaded
Establishment context
- NAICS code
- 326121
- SIC code (legacy)
- 3089
- Employees
- 30
- Ownership type
- A
- Industry flags
- Manufacturing safety.
Citations
6 citations on file for this inspection.
5(a)(1)
- Issued
- Oct 10, 2003
- Abate by
- Nov 12, 2003
- Penalty
- Initial $875 · Current $569 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazard of being crushed by the forklift and/or falling off the forklift. a)Molding Area, on or about 10/02/03: Employee was operating a Clark Fork Truck model number 500EC, without any seat belts. b)Molding Area, on or about 10/02/03: Employee was operating a Clark Fork Truck model number 500EC, without a battery restraint device approved by the manufacturer. ABATEMENT NOTES: Among other methods, one feasible and acceptable abatement method to correct this hazard is to: 1. Install seat belts on the Clark Fork Truck as per retrofit kit from manufacturer. 2. Install battery restraint device on the Clark Fork Truck as per retrofit kit from the manufacturer. 3. Follow the requirements of American National Standards for Safety Standard for Low Lift and High Lift Trucks (ASME B56.1-1993, Chapter 7.38) Abatement certification must be submitted for this item.
Recent events (2)
- — I (S) $568.50
- — Z (S) $875.00
1910.178 A04
- Issued
- Oct 10, 2003
- Abate by
- Nov 12, 2003
Recent events (2)
- — I (S)
- — Z (S)
1910.178 M10
- Issued
- Oct 10, 2003
- Abate by
- Oct 28, 2003
Recent events (2)
- — I (S)
- — Z (S)
1910.219 B01
- Issued
- Oct 10, 2003
- Abate by
- Oct 28, 2003
- Penalty
- Initial $875 · Current $569 Reduced
Recent events (2)
- — I (S) $568.50
- — Z (S) $875.00
1910.219 D01
- Issued
- Oct 10, 2003
- Abate by
- Oct 28, 2003
- Penalty
- Initial $700
Recent events (2)
- — I (O)
- — Z (S) $700.00
1910.219 E02 I
- Issued
- Oct 10, 2003
- Abate by
- Oct 28, 2003
Recent events (2)
- — I (O)
- — Z (S)
More inspections at Bo-Mer Plastics
View Bo-Mer Plastics's full OSHA safety record →
More inspections in this industry (NAICS 326121)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 306311937.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.