WINNSBORO, TX —
OSHA Inspection: HEFLIN BUILDING SYSTEMS, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of HEFLIN BUILDING SYSTEMS, INC. in 315 N. MAIN, WINNSBORO, TX 75494 (NAICS 238140). OSHA activity number 307486746.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- HEFLIN BUILDING SYSTEMS, INC.
- Site address
- 315 N. MAIN
- City
- WINNSBORO
- State
- TX
- ZIP
- 75494
- Mailing
- 2308 MICIGAN COURT, ARLINGTON, TX 76016
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238140
- SIC code (legacy)
- 1741
- Employees
- 2
- Ownership type
- A
Citations
1 citation on file for this inspection.
5(a)(1)
- Issued
- Nov 24, 2004
- Abate by
- Nov 30, 2004
- Penalty
- Initial $1,500 · Current $900 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that: On September 22, 2004, at the job site of 315 N. Main, Winnsboro, TX 75494, an employee was exposed to a fall hazard when he was elevated approximately 20 feet on a platform which was attached to a SkyTrak, and without fall protection. Acceptable means of abatement may include but are not limited to the following: a) SkyTrak, Owners/Operators Manual: Elevating Personnel Use an approved work platform to lift or lower personnel. NEVER move the vehicle with the work platform in a raised position or with personnel on board. 1) Make sure that the work platform is securely attached to the quick attach or forks. Follow the platform manufacturer's instructions. 2) Make sure that the platform, carriage and forks are secured to prevent them from pivoting from side to side. 3) Ensure that the vehicle has a firm footing and is level. 4) Place the travel select lever in (N) Neutral. 5) Engage the emergency brake switch. Blocking of the vehicle wheels is also recommended. 6) Level the platform in both the side to side and front to back directions before use. b) As incorporated by reference to both 29CFR 1910.178 and 29CFR 1926.602 ASME B56.1- 2000:4.17, specifies instructions on elevating personnel and ASME B56.1-2000: 7.36, specifies design requirements for the personnel platform.
Recent events (2)
- — I (S) $900.00
- — Z (S) $1500.00
More inspections at Heflin Building Systems, INC.
View Heflin Building Systems, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 238140)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 307486746.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.