NEWARK, NY —
OSHA Inspection: HALLAGAN MANUFACTURING COMPANY INC
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of HALLAGAN MANUFACTURING COMPANY INC in 500 HOFFMAN STREET, NEWARK, NY 14513 (NAICS 337121). OSHA activity number 307689760.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- HALLAGAN MANUFACTURING COMPANY INC
- Site address
- 500 HOFFMAN STREET
- City
- NEWARK
- State
- NY
- ZIP
- 14513
- Mailing
- P.O. BOX 268, NEWARK, NY 14513
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 337121
- SIC code (legacy)
- 2512
- Employees
- 85
- Ownership type
- A
Citations
9 citations on file for this inspection.
5(a)(1)
- Issued
- Apr 7, 2005
- Abate by
- Jul 11, 2005
- Penalty
- Initial $875 · Current $525 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazard of falling into the elevator shaft and/or being struck by the elevator car: a)On or about 2/24/05: Freight/passenger elevator provided for moving furniture between two floors was not provided with car and hoistway doors or gates with an interlock system at each floor. Among other methods, acceptable and feasible abatement methods to correct these hazards are to: 1.Install car doors or gates at the entrance of the elevator car with an electric contact that shall be positively opened by a lever or other device attached to and operated by the door or gate; and that shall be maintained in the open position by the action of gravity or by a restrained compression spring, or both, or by a positive mechanical means in accordance with ANSI/ASME Z17.3-1989, Safety Code for Existing Elevators and Escalators, Section 3.4.2. 2.Install hoistway doors or gates at landing openings which guard the full width of the opening and guard the height to a minimum of 6 feet above the landing in accordance with ANSI/ASME Z17.3-1989, Safety Code for Existing Elevators and Escalators, Section 2.6. 3.Install door interlocks on the hoistway doors. The interlock device shall lock the door in the closed position before the elevator can be operated and prevent the door from opening when the platform is not parked on that level in accordance with ANSI/ASME A17.3-1986 Safety Code for Existing Elevators and Escalators, Section 2.7.1. Abatement certification must be submitted for this item.
Recent events (2)
- — I (S) $525.00
- — Z (S) $875.00
1910.23 D01 I
- Issued
- Apr 7, 2005
- Abate by
- Apr 25, 2005
- Penalty
- Initial $525 · Current $315 Reduced
Recent events (2)
- — I (S) $315.00
- — Z (S) $525.00
1910.213 B03
- Issued
- Apr 7, 2005
- Abate by
- Apr 25, 2005
- Penalty
- Initial $525 · Current $315 Reduced
Recent events (2)
- — I (S) $315.00
- — Z (S) $525.00
1910.215 A02
- Issued
- Apr 7, 2005
- Abate by
- Apr 12, 2005
- Penalty
- Initial $700 · Current $420 Reduced
Recent events (2)
- — I (S) $420.00
- — Z (S) $700.00
1910.215 A04
- Issued
- Apr 7, 2005
- Abate by
- Apr 12, 2005
Recent events (2)
- — I (S)
- — Z (S)
1910.215 B09
- Issued
- Apr 7, 2005
- Abate by
- Apr 12, 2005
Recent events (2)
- — I (S)
- — Z (S)
1910.242 B
- Issued
- Apr 7, 2005
- Abate by
- Apr 12, 2005
- Penalty
- Initial $700 · Current $420 Reduced
Recent events (2)
- — I (S) $420.00
- — Z (S) $700.00
1910.303 G02 I
- Issued
- Apr 7, 2005
- Abate by
- Apr 12, 2005
- Penalty
- Initial $875 · Current $525 Reduced
Recent events (2)
- — I (S) $525.00
- — Z (S) $875.00
1910.304 F04
- Issued
- Apr 7, 2005
- Abate by
- Apr 12, 2005
- Penalty
- Initial $875 · Current $525 Reduced
Recent events (2)
- — I (S) $525.00
- — Z (S) $875.00
More inspections at Hallagan Manufacturing Company INC
View Hallagan Manufacturing Company INC's full OSHA safety record →
More inspections in this industry (NAICS 337121)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 307689760.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.