BUFFALO, NY —
OSHA Inspection: DATESWEISER FURNITURE CORPORATION
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of DATESWEISER FURNITURE CORPORATION in 1700 BROADWAY, BUFFALO, NY 14212 (NAICS 337211). OSHA activity number 308044171.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- DATESWEISER FURNITURE CORPORATION
- Site address
- 1700 BROADWAY
- City
- BUFFALO
- State
- NY
- ZIP
- 14212
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 337211
- SIC code (legacy)
- 2521
- Employees
- 105
- Ownership type
- A
Citations
5 citations on file for this inspection.
5(a)(1)
- Issued
- Feb 17, 2005
- Abate by
- Apr 5, 2005
- Penalty
- Initial $3,500 · Current $2,100 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazard of being caught in an in-running nip/pinch points on a moving belt conveyor and were unable to shut the conveyor off quickly because no emergency stop pull cord or similar device was present: a) On or about 09/22/04, in the Veneer Dept.: An employee's hand got caught in an in- going nip point at the "turnaround roll" of the mylar belt conveyor and his arm was amputated when it got caught in the nip point at the bottom chain and sprocket wheel of the drive system for the mylar belt conveyor at the exit end of the Italpresse Hot Oil Veneer Press. Among others, a feasable method to eliminate or materially reduce this hazard is to equip the mylar belt conveyor with permanently installed pull cords or similar stop controllers which comply with ASME B20.1-1996, Safety Standard For Conveyors and Related Equipment, Section 5.11.2(c) and Section 6.1.2(c). ABATEMENT DOCUMENTATION REQUIREDATION
Recent events (2)
- — I (S) $2100.00
- — Z (S) $3500.00
1910.147 C04 I
- Issued
- Feb 17, 2005
- Abate by
- Feb 28, 2005
- Penalty
- Initial $3,500 · Current $2,100 Reduced
Recent events (2)
- — I (S) $2100.00
- — Z (S) $3500.00
1910.147 C07 IA
- Issued
- Feb 17, 2005
- Abate by
- Feb 28, 2005
1910.212 A01
- Issued
- Feb 17, 2005
- Abate by
- Feb 28, 2005
- Penalty
- Initial $3,500 · Current $2,100 Reduced
Recent events (2)
- — I (S) $2100.00
- — Z (S) $3500.00
1910.219 F03
- Issued
- Feb 17, 2005
- Abate by
- Apr 15, 2005
Recent events (2)
- — I (S)
- — Z (S)
More inspections at Datesweiser Furniture Corporation
View Datesweiser Furniture Corporation's full OSHA safety record →
More inspections in this industry (NAICS 337211)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 308044171.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.