BOISE, ID —
OSHA Inspection: SYSTEMS TECH
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of SYSTEMS TECH in 8109 W. FRANKLIN RD., BOISE, ID 83709 (NAICS 238210). OSHA activity number 308342310.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- SYSTEMS TECH
- Site address
- 8109 W. FRANKLIN RD.
- City
- BOISE
- State
- ID
- ZIP
- 83709
- Mailing
- 3131 HARVARD, BOISE, ID 83705
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238210
- SIC code (legacy)
- 1731
- Employees
- 4
- Ownership type
- A
- Industry flags
- Construction safety.
Citations
2 citations on file for this inspection.
5(a)(1)
- Issued
- Nov 13, 2006
- Abate by
- Nov 17, 2006
- Penalty
- Initial $600 · Current $300 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish a place of employment which was free from recognized hazards that were likely to cause death or serious physical harm to employees in that an employee was exposed to a fall hazard by standing on two midrails of an elevated scissor lift platform; (a)On July 25, 2006, and at times prior thereto, an employee working in the warehouse area of the Cabela's store remodel was exposed to a fall of approximately 26 feet when he stood on the midrails of an elevated JLG scissor lift model 1930ES while reaching over his head to straighten wires in a cable tray. One feasible means of abatement is to follow the requirements of ANSI A92.3 -1999 Standards for Self-Propelled Elevating Work Platforms and to follow the manufactures instructions to " Keep both feet firmly positioned on the platform floor at all times. Note: Abatement certification required for this item. Evaluation of 5(a)(1) (a)The employer failed to keep the workplace free of a hazard to which employees of that employer were exposed; employee was observed performing an unsafe act. (b)The hazard was recognized; the employee and employer both recognize the hazard (c)The hazard was causing or was likely to cause death or serious physical harm; Serious injury or even death could result of a fall from 26 feet onto concrete. (d)There was a feasible and useful method to correct the hazard. See the feasible means of abatement above. Or in the Alternative 29 CFR 926.451(g)(1)(vii): Each employee was not protected by the use of personal fall arrest systems or guardrail systems meeting the requirements of this standard. (a)Job Site; on July 25, 2006, an employee was exposed to a fall hazard of approximately 26 feet while working from the mid rail of a JGL scissor lift, model 1930ES. Note: Abatement certification is required for this item.
Recent events (2)
- — I (S) $300.00
- — Z (S) $600.00
1926.454 A
- Issued
- Nov 13, 2006
- Abate by
- Nov 17, 2006
Recent events (2)
- — I (O)
- — Z (O)
More inspections at Systems Tech
View Systems Tech's full OSHA safety record →
More inspections in this industry (NAICS 238210)
More inspections in ID
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 308342310.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.