NORTH POLE, AK —
OSHA Inspection: GIO ALASKA TIMBER INCORPORATED
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of GIO ALASKA TIMBER INCORPORATED in 1631 OLD RICHARDSON HIGHWAY, NORTH POLE, AK 99705 (NAICS 321113). OSHA activity number 308539154.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- GIO ALASKA TIMBER INCORPORATED
- Site address
- 1631 OLD RICHARDSON HIGHWAY
- City
- NORTH POLE
- State
- AK
- ZIP
- 99705
- Mailing
- POB 74638, FAIRBANKS, AK 99707
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321113
- SIC code (legacy)
- 2421
- Employees
- 12
- Ownership type
- A
- Industry flags
- Manufacturing safety.
Citations
48 citations on file for this inspection.
1910.138 B
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
- Penalty
- Initial $1,500 · Current $975 Reduced
Recent events (2)
- — I (S) $975.00
- — Z (S) $1500.00
1910.39 C01
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.1200 E01
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.132 A
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
- Penalty
- Initial $1,500 · Current $975 Reduced
Recent events (2)
- — I (S) $975.00
- — Z (S) $1500.00
1910.132 D01
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.132 D02
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.132 F04
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.95 B01
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.95 D01
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.95 K01
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.147 C01
- Issued
- Jan 19, 2007
- Abate by
- Feb 7, 2007
- Penalty
- Initial $1,500 · Current $975 Reduced
Recent events (2)
- — I (S) $975.00
- — Z (S) $1500.00
1910.147 C04 II
- Issued
- Jan 19, 2007
- Abate by
- Feb 7, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.178 L01 I
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
- Penalty
- Initial $1,500 · Current $975 Reduced
Recent events (2)
- — I (S) $975.00
- — Z (S) $1500.00
1910.178 M05 I
- Issued
- Jan 19, 2007
- Abate by
- Jan 24, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.178 P01
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.213 A12
- Issued
- Jan 19, 2007
- Abate by
- Feb 7, 2007
- Penalty
- Initial $1,500 · Current $975 Reduced
Recent events (2)
- — I (S) $975.00
- — Z (S) $1500.00
1910.213 C01
- Issued
- Jan 19, 2007
- Abate by
- Feb 7, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.213 G01
- Issued
- Jan 19, 2007
- Abate by
- Feb 7, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.212 A01
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.213 B01
- Issued
- Jan 19, 2007
- Abate by
- Jan 24, 2007
- Penalty
- Initial $1,500 · Current $975 Reduced
Recent events (2)
- — I (S) $975.00
- — Z (S) $1500.00
1910.213 B03
- Issued
- Jan 19, 2007
- Abate by
- Jan 24, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.265 C18 I
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
- Penalty
- Initial $1,050 · Current $683 Reduced
Recent events (2)
- — I (S) $682.50
- — Z (S) $1050.00
1910.303 A
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
- Penalty
- Initial $1,500 · Current $975 Reduced
Recent events (2)
- — I (S) $975.00
- — Z (S) $1500.00
1910.305 B01
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.305 B01
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (S)
- — Z (S)
1910.334 A02 II
- Issued
- Jan 19, 2007
- Abate by
- Feb 7, 2007
Recent events (2)
- — I (S)
- — Z (S)
1800607501
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
- Penalty
- Initial $2,100 · Current $1,365 Reduced
General-duty citation text
Sec. 18.60.075. Safe Employment. (a) An employer shall do everything necessary to protect the life, health, and safety of employees including, but not limited to: (1) complying with all occupational safety and health standards and regulations adopted by the department; (2)furnishing and prescribing the use of suitable protective equipment, safety devices, and safeguards as are prescribed for the work and work place; (3) adopting and prescribing control or technological procedures, and monitoring and measuring employee exposure in connection with hazards, as may be necessary for the protection of employees; and (4) furnishing to each employee employment and a place of employment that are free from recognized hazards that, in the opinion of th4e commissioner, are causing or are likely to cause death or serious physical harm to the employees. EXAMPLE:There were no written procedures for equipment operation and no thorough training of sawmill equipment operators. The safety officer said that the saw operators knew how to take care of the machines but there is no documentation for training, and the manual for the Hamil gang-saw is written in Korean, and the manuals for the Scragg-saw and edger-saw are missing. The assistant manager said that new employees were trained by the current operators but without written procedures and documented operator training by a qualified trainer, there is no assurance that new operators know to observe all operating procedures and safety practices with each piece of equipment. An industrial accident occurred the GIO sawmill on July 24, 2006 where an employee suffered an accident with an edger saw with the result that he had two fingers and half of his right hand amputated. The employee reached into the rear of the saw to clean out sawdust debris and made hand contact with the edger blades. The employee was an occasional operator of the saw but was not familiar with all of the switches and control functions to safely operate the saw. Employee saw operators had not received training and complete operating instructions to enable them to safely operate all of the saws in the sawmill. During the inspection six employees were interviewed and asked to demonstrate the E430 Edger Saw control switch operations to start and stop the saw. The Manager, Asst Manager, Safety Officer, the primary E430 saw operator, an occasional E430 saw operator, and the LT300 mill saw operator were the employees interviewed. None of the six knew the functions of a rotary switch on the edger-saw electrical panel. With the rotary switch in the "Hand" position, the saw turned on when the electrical panel knife switch was closed. I asked them to turn off the saw with the emergency power switches and they were not able to shut off the saw with either of the 2 emergency power controls. None of the six knew that when the rotary switch was turned to the "Hand" position that the emergency shut-off switches were bypassed. Causal factors contributing to the accident include: Inadequate employee training. The employer had no program to ensure that all operators had been effectively trained to safely operate equipment. The accident victim was not familiar with all edger saw operatingcontrols. This employee had not been trained to recognize the potential hazard that the saw blades could still be in operation. The employer failed to implement written procedures for the control of hazardous energy. Manuals for the E430 Edger-saw and Skragg-saw were not available for employee reference. The Hamil gang-saw manual was written in Korean and the saw operators could not read Korean.There were no written operating procedures for the E430 Edger-saw, Skragg-saw, or Hanil gang-saw. The employer failed to implement a safety program. Prior to the 7/24/06 amputation accident, there was no safety officer, or safety meetings. A rotary electrical switch installed on the Edger-saw electrical panel bypassed the two operator emergency stop controls that shut down the saw. As an apparent "Imminent Danger" hazard I told the manager that the machine must not be used until the safe operation of the saw could be verified and that operators were competent to operate the saw. The manager agreed and a lock was placed on the knife switch to lock out the saw and the main breaker powering the knife switch panel was turned off.
Recent events (2)
- — I (S) $1365.00
- — Z (S) $2100.00
1910.252 B02 III
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.252 B03
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.253 A04
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.253 B02 IV
- Issued
- Jan 19, 2007
- Abate by
- Feb 7, 2007
Recent events (2)
- — I (O)
- — Z (O)
18006058
- Issued
- Jan 19, 2007
- Abate by
- Jan 24, 2007
- Penalty
- Initial $300 · Current $195 Reduced
Recent events (2)
- — I (O) $195.00
- — Z (O) $300.00
18006068
- Issued
- Jan 19, 2007
- Abate by
- Jan 24, 2007
- Penalty
- Initial $300 · Current $195 Reduced
Recent events (2)
- — I (O) $195.00
- — Z (O) $300.00
1904.29 B03
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
- Penalty
- Initial $300 · Current $195 Reduced
Recent events (2)
- — I (O) $195.00
- — Z (O) $300.00
1910.7 B03
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.23 D01
- Issued
- Jan 19, 2007
- Abate by
- Jan 24, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.24 B
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.36 G02
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.157 C01
- Issued
- Jan 19, 2007
- Abate by
- Jan 24, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.157 G01
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.176 B
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.219 C04 I
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.219 C04 II
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.242 B
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.243 C03
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.265 C04 I
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.265 E02 IC
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
1910.265 C20 III
- Issued
- Jan 19, 2007
- Abate by
- Mar 8, 2007
Recent events (2)
- — I (O)
- — Z (O)
More inspections in this industry (NAICS 321113)
More inspections in AK
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 308539154.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.