WHEAT RIDGE, CO ·
OSHA Inspection: MARBLE TEC FABRICATION INC.
Planned inspection · Health discipline
At a glance
On , OSHA opened a planned health inspection of MARBLE TEC FABRICATION INC. in 11771 W 49TH AVENUE UNIT A, WHEAT RIDGE, CO 80033 (NAICS 327991). OSHA activity number 309189132.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- MARBLE TEC FABRICATION INC.
- Site address
- 11771 W 49TH AVENUE UNIT A
- City
- WHEAT RIDGE
- State
- CO
- ZIP
- 80033
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Health
- Advance notice
- No
- Union status
- Non-union (N)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 327991
- SIC code (legacy)
- 3281
- Employees
- 14
- Ownership type
- Private (A)
Citations
3 citations on file for this inspection.
5(a)(1)
- Issued
- Oct 14, 2005
- Abate by
- Nov 2, 2005
- Penalty
- Initial $1,500 · Current $400 Reduced
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to crushing hazards when transporting natural stone slabs: 1) On September 13, 2005, and at prior times, employees who were transporting natural stone slabs from A-frame racks into the shop were exposed to crushing hazards, in that employees on each end of the slab supported the stone slab by hand in the vertical position on the A-frame, while an employee stood in the fall shadow of the slab to attach fork lift scissor clamp. Among other methods, some feasible and acceptable abatement methods are as follows: a) If a mechanical below the hook lifting device is required to be placed on the slab, the slab should be mechanically stabilized or should be resting at a slight angle (not hand supported) against the A-frame rack while the lifting device is situated. A spacer or wedge may be inserted behind the slab to be lifted to provide space at the top to facilitate placement of the mechanical lifting device. The slabs may also be supported with straps wrapped around the entire A-frame rack. The straps could then be loosened just enough to hand raise the slab to the vertical position but not enough to allow the slab to fall. The mechanical lifting device could then be placed on the slab. b) Institute and enforce written procedures in which employees are prohibited from standing in the fall shadow of unstable and/or hand supported stone slabs. Institute written procedures for lifting and transporting stone slabs, and train employees on these procedures. Abatement Note: Abatement certification and documentation is required for this item (see enclosed "Sample Abatement-Certification Letter").-Certification
Recent events (2)
- · I (S) $400.00
- · Z (S) $1500.00
1910.95 C01
- Issued
- Oct 14, 2005
- Abate by
- Dec 15, 2005
- Penalty
- Initial $375 · Current $100 Reduced
Recent events (2)
- · I (S) $100.00
- · Z (S) $375.00
1910.303 B02
- Issued
- Oct 14, 2005
- Abate by
- Oct 19, 2005
Recent events (2)
- · I (O)
- · Z (O)
More inspections in this industry (NAICS 327991)
More inspections in CO
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 309189132.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.