OSHA Inspection: EUROCRAFT WALL INDUSTRIES, INC.

Issued

Jan 17, 2006

Abate by

Jan 23, 2006

Penalty

Initial $2,500 · Current $2,500

General-duty citation text

Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The
employer did not furnish
employment and a place of employment which were free from recognized
hazards that were
causing or likely to cause death or serious physical harm to employees in
that employees were
exposed to:
Construction Site: The Terex Aerial Scissor Lift, serial #99360123 with
maintenance
defects was not taken out of service until all maintenance defects were
repaired or
replaced, exposing employees to overturning of the lift.
Among other methods, one feasible and acceptable abatement method to
correct this
hazard is:
To comply with ANSI/SIA 92.6, Para 7.3, dated 1190. Aerial platforms that
are
not in proper operating condition shall be immediately removed from
service until
repaired.

Issued

Jan 17, 2006

Abate by

Feb 3, 2006

Penalty

Initial $2,500 · Current $2,500

General-duty citation text

Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The
employer did not furnish
employmnent and a place of employment which were free from recognized
hazards that were
causing or likely to cause death or serious physical harm to employees in
that employees were
exposed to:
Construction site: The Terex Aerial Scissor Lift, serial number 99360123
was not being
operated by a fully qualified operator, exposing employees to overturning
of the lift.
Among other methods, one feasible and acceptable abatement method to
correct this
hazard is:
To comply with ANSI/SIA 92.6, paragraph 7.6 through 7.6.2, dated 1990.
Insure the
operator is fully trained in accordance with the manufacture operating and
maintenance
manual and trained in the model of the aerial lift he/she will be
operating. Trainee
records maintained by the user for at least three years.

Issued

Jan 17, 2006

Abate by

Feb 3, 2006

Penalty

Initial $2,500 · Current $2,500

General-duty citation text

Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The
employer did not furnish
employment and a place of employment which were free from recognized
hazards that were
causing or likely to cause death or serious physical harm to employees in
that employees were
exposed to:
Construction Site: The Terex Aerial Scissor Lift, serial number 99360123,
operator
could not read or understand the manufacture's operating instructions and
user's safety
rules in it's printed version.
Among other methods, one feasible and acceptable abatement method to
correct his
hazard is:
To comply with ANSI/SIA 92.6, paragraph 7.7(1) through 7.7(4), the
operator has been
instructed by a qualified person in the intended purpose and function of
each control,
read and understood the manufacturer's operating instruction and user's
safety rules.

Issued

Jan 17, 2006

Abate by

Jan 23, 2006

Penalty

Initial $2,500 · Current $2,500

General-duty citation text

Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The
employer did not furnish
employmnent and a place of employment which were free from recognized
hazards that were
causing or likely to cause death or serious physical harm to employees in
that employees were
exposed to:
Construction Site: The Terex Aerial Scissor Lift, serial number 99360123,
areas where
the scissor lift was used were not inspected for drop-offs or holes,
bumps, and floor
obstructions before being used in such areas, exposing employees to
overturning of the
lift.
Among other methods, one feasible and acceptable abatement method to
correct the
hazard is:
To comply with ANSI/SIA 92.6 paragraph 7.8 (1) through 7.8 (9). Before the
aerial
platform is used and during the use, the user shall check the area in
which the aerial
platform is to be used for possible hazards such as, but not limited to
drop-offs, holes,
bumps, floor obstruction, debris, and other possible unsafe conditions.